User manual HITACHI CPX4

[. . . ] Projector CPX4 User's Manual (detailed) Operating Guide SD RD CA Thank you for purchasing this projector. WARNING Before using this product, please read all manuals for this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. [. . . ] (4) To change an already inserted character, press the button to move the cursor to the first line, and use the / buttons to move the cursor on the character to be changed. After pressing the ENTER or INPUT/ENTER button, the character is selected. (5) To finish entering text, move the cursor to the SAVE on screen and press the ENTER or INPUT/ENTER button. To revert to the previous name without saving changes, move the cursor to the CANCEL on screen and press the ENTER or INPUT/ENTER button. The selected template pattern can be displayed when the MY BUTTON allocated to the TEMPLATE function is pressed (42). DOT-LINE4 ó DOT-LINE3 ó DOT-LINE2 TEST PATTERN ó DOT-LINE1 SOURCE NAME TEMPLATE 39 OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the / cursor buttons, and press the cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table. Item Description Using the / buttons turns on/off the automatic signal search function. TURN ON ó TURN OFF When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order. Then when an input is found, the projector will stop searching and display the image. COMPUTER IN ð MIU VIDEO S-VIDEO Using the / buttons turns on/off the automatic keystone function. TURN ON ó TURN OFF TURN ON : Automatic keystone distortion correction will be executed whenever changing the slant of the projector. Please execute the AUTO KEYSTONE EXECUTE in the SETUP Menu for automatic keystone distortion correction. · When the projector is suspended from the ceiling this feature will not function properly so select the TURN OFF. · This function will be unavailable when the Transition Detector is on (48). TURN ON ó TURN OFF When set to the TURN ON, the lamp in projector will be automatically turned on without the usual procedure (14), only when the projector is supplied with the power after the power was cut while the lamp was on. · This function does not work as long as the power has been supplied to the projector while the lamp is off. · After turning the lamp on by the AUTO ON function, if neither input nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO OFF function (41) is disabled. AUTO SEARCH AUTO KEYSTONE AUTO ON (continued on next page) 40 OPTION menu OPTION menu (continued) Item Description Using the / buttons adjusts the time to count down to automatically turn the projector off. 0 minute = DISABLE) AUTO OFF When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL port during the corresponding time, projector will not be turned off. The lamp time is the usage time of the lamp, counted after the last resetting. [. . . ] If the same indication is displayed after the remedy, please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH. It is time to clean the air filter. Lighting In Green Simultaneous blinking in Red Please immediately turn the power off, and clean or change the air filter referring to the section "Air Filter". After cleaning or changing the air filter, please be sure to reset the filter timer. After the remedy, reset the power to ON. Lighting In Green Blinking in Green for approx. 3 seconds Alternative blinking in Red There is a possibility that the interior portion has become overcooled. Please use the unit within the usage temperature parameters (5°C to 35°C). [. . . ]