User manual HITACHI CP-X201

[. . . ] Projector CP-X201/CP-X301/CP-X401/CP-X450 User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING Before using this product, please read all manuals for this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. [. . . ] · When the projector is inclined to near ±30 degree or over, this function may not work well. · This function will be unavailable when the Transition Detector is on (49). Shrink the top of the image ó Shrink the bottom of the image · The adjustable range of this function will vary with the type of input signal. · This function will be unavailable when the Transition Detector is on (49). AUTO KEYSTONE EXECUTE KEYSTONE (continued on next page) 33 SETUP menu SETUP menu (continued) Item WHISPER Description Using the / buttons turns off/on the whisper mode. NORMAL ó WHISPER · When WHISPER is selected, acoustic noise and screen brightness are reduced. Using the / buttons switches the mode for mirror status. MIRROR NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (49) will be displayed when projector is restarted after the power switch is turned off. Using / buttons switches the standby mode setting between NORMAL and SAVING. NORMAL ó SAVING When SAVING is selected, the power consumption in the standby mode is lowered with some functional restriction as below: · When SAVING is selected, the RS-232C communication control is disabled except to turn the projector on while the projector is in the standby mode. · When SAVING is selected, any setting of the MONITOR OUT ( below) and AUDIO (35) in the standby mode is invalid, and no signal is output from both of MONITOR OUT and AUDIO OUT ports in the standby mode. The combination of a picture shown on screen and output from the MONITOR OUT port can be arranged in the menu. The picture coming into the port selected in the (2) is output to the MONITOR OUT port while an image from the port chosen in the (1) is on screen. (1) Choose a picture input port using / buttons. QUIT ó COMPUTER 1 ó COMPUTER 2 (COMPUTER IN1) (COMPUTER IN2) STANDBY VIDEO ó S-VIDEO ó COMPONENT (Y, Cb/Pb, Cr/Pr) STANDBY MODE MONITOR OUT · Choose STANDBY, to select the output signal from the MONITOR OUT port in the standby mode. · While QUIT is selected, pressing the button returns to the previous menu. 1 (COMPUTER IN1) ó OFF Choosing the COMPUTER 2 allows the following choice. 2 (COMPUTER IN2) ó OFF Choosing other input or STANDBY allows the following choice. 1 (COMPUTER IN1) ó 2 (COMPUTER IN2) ó OFF · OFF disables the MONITOR OUT port. 34 AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the / cursor buttons, and press the cursor button or the ENTER button to execute the item. Then perform it according to the following table. Item VOLUME SPEAKER Description Using the / buttons adjusts the volume. High ó Low Using the / buttons turns on/off the built-in speaker. TURN ON ó TURN OFF When TURN OFF is selected, the built-in speaker does not work. The combination of a picture and audio input port can be arranged in the menu. The audio coming into the port selected in the (2) is output while an image from the port chosen in the (1) is on screen. [. . . ] If the same indication is displayed after the remedy, please contact your dealer or service company. (Continued on next page) 60 Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Description There is a possibility that the interior portion has become heated. Blinking In Red or Lighting In Red Turned off Lighting In Red Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again. If the same indication is displayed after the remedy, please set FAN SPEED of SERVICE item in OPTION menu to HIGH (43). It is time to clean the air filter. Lighting In Green Simultaneous blinking in Red Please immediately turn the power off, and clean or change the air filter referring to the section "Cleaning and replacing the air filter". After cleaning or changing the air filter, please be sure to reset the filter timer. [. . . ]