User manual HITACHI CPL850W

[. . . ] If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferable a qualified electrician. [. . . ] · Do not apply unnecessary force from the upper side when lifting the projector. Otherwise, projector may be damaged or a finger could be caught and cause injury. 11 Basic operations To project the picture 4 3 MUTE 2 RESET MENU STANDBY/ON MUTE FREEZE MAGNIFY VOLUME OFF POSITION ON INPUT LASER LAMP ON TEMP 5 7 STANDBY/ON RESET MENU ON RIGHT MOUSE ON TIMER VIDEO INPUT 2 7 BLANK RGB 1 1 2 3 4 5 6 7 Turn the MAIN POWER switch of the projector on. [ I : ON] · The ON indicator will light up orange. Press the STANDBY/ON button. · The ON indicator blinks (green) and then lights (green). · The ON indicator will blink green during warm-up and light up. · Power cannot be turned on even if the STANDBY/ON button is pressed within 60 seconds after power is turned off, since the lamp has cooled preparing for next lighting. Remove the lens cap. Power on all connected equipment. The method of connecting various equipment, see on the page 19~27. Press the INPUT button or the INPUT SELECT (VIDEO or RGB) button to select the source of the signal to be projected on the screen. Example on-screen display · The selected signal input is displayed at the bottom right of the screen for 3 seconds. 12 Basic operations (continued) To turn off the power 1 RESET STANDBY/ON MUTE FREEZE MAGNIFY VOLUME 3 MENU MUTE INPUT LAMP ON TEMP OFF POSITION ON LASER STANDBY/ON RESET MENU ON RIGHT MOUSE ON TIMER VIDEO INPUT 1 BLANK RGB 2 1 2 3 Press the STANDBY/ON button, for 1 second. · The ON indicator lights up orange and the lamp turns off. (About 1 minute later), the fan stops and the indicator blinks orange. · Press the STANDBY/ON button for short time (less than 1 second), the projector do not set in standby mode. Turn the MAIN POWER switch of the projector off. [ Install the lens cap. : OFF] Caution · To reduce temperature inside the projector (cooling down), fan will rotate for about 1 minute after the lamp is turned off. · Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. PLUG&PLAY This projector complies with VESA DDC1/2B specifications. PLUG&PLAY is a system with computer, peripherals (including projectors), and operating system. It works when the projector is connected to DDC (Display Data Channel) ready computer that is running an operating system software that incorporates plug & play functionality. SETUP INPUT IMAGE OPT. MIRROR BLANK REVEAL MESSAGE MIRROR NORMAL H : INVERT V : INVERT H&V : INVERT BLANK WHITE BLUE BLACK SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. REVEAL FAST MEDIUM SLOW MESSAGE TURN ON TURN OFF Adjustment Item Details of adjustment Inverts the picture horizontally or vertically. When start up screen is displayd, screen will blank out 5 minutes later. (VOLUME, Input selection display) MIRROR BLANK REVEAL MESSAGE 17 Adjustments and functions (continued) OPT. The menu OPT. allows you to control communication function etc. SETUP INPUT IMAGE OPT. COM. BITS TIMER LANGUAGE AUTO OFF START UP SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. COM. BITS 7N1 8N1 TIMER 15 min. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. LANGUAGE ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO NORSK NEDERLANDS START UP AUTO OFF 0 min. SPEED (COMMUNICATION SPEED) Details of adjustment Selects the data speed of transmission. (five kinds) Selects the data format or transmission 7N1. . . 7 data bits, No parity, 1 stop bit. (English, Francais, Deutsch, Espanol, Italiano, Norsk, Nederlands) Sets time (minutes) from the start of displaying start up screen (No input is detected or sync is out of range) to turning the power OFF. "0" is stop and another "1~99" Sets/releases start up screen displayed when power is turned on, or when no input is detected or sync is out of range. COM. BITS (COMMUNICATION BITS) TIMER LANGUAGE AUTO OFF START UP 18 Connection to the video signal terminals 1. [. . . ] (count down. ) When the lamp has 2, 000 hours or more on it, the message will blink, and the power will turns off after 10 minutes. (See page 19, 20) The horizontal frequency of the input signal exceeds the range of the projector, it cannot be displayed. (See page 20, 21) Clean the air filter of remove the blocking ventilation holes. (See page 28) 30 *1 This message are not displayed after 3 minutes. [. . . ]