User manual HITACHI CPL550E

[. . . ] CAUTION This symbol indicates information that , if ignored, could result possibly in personal injury or physical damage due to incorrect handling. Please refer to the pages written following this symbol. NOTE · The information in this manual is subject to change without notice. · The manufacture assumes no responsibility for any errors that may appear in this manual. · The reproduction, transmission or use of this document or contents is not permitted without express written authority. [. . . ] Upper in the data Lower in the data · The adjustable range of this function will vary with the type of input signal. · When the V:INVERT or the H&V:INVERT is selected under the item MIRROR, if the projector screen is inclined or if the projector is angled downward, this function may not work correctly. · When the zoom adjustment is set to the TELE side, this correction may be excessive. NORMAL WHISPER · When the WHISPER is selected, acoustic noise and screen brightness are reduced. MIRROR NORMAL H:INVERT V:INVERT H&V:INVERT VOLUME Using the buttons / adjusts the volume. High Low MENU [RGB] PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU KEYSTONE WHISPER MIRROR VOLUME :SELECT +0 NORMAL NORMAL 16 KEYSTONE WHISPER 32 Multifunctional settings SCREEN Menu With the SCREEN menu, items shown in the table below can be performed. Select an item using the cursor buttons / on the projector or remote control, and press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description Using the buttons / switches the OSD (On Screen Display) language. LANGUAGE ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO NORSK NEDERLANDS PORTUGUÊS SVENSKA MENU [RGB] PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU LANGUAGE MENU POSITION OSD BRIGHT BLANK START UP MyScreen MyScreen Lock MESSAGE :SELECT 5 BLACK ORIGINAL TURN OFF TURN ON SUOMI POLSKI MENU POSITION Using the buttons /// adjusts the menu position. To quit the operation, press the MENU button on the remote control or keep no operation for 10 seconds. Using the buttons / switches the brightness level of the OSD (On Screen Display). "AUTO IN PROGRESS" while automatically adjusting "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "Searching . . . . " while searching for an input signal "Detecting. . . . " when an input signal is detected The indication of the input signal by changing The indication of the aspect ration by changing . ENGLISH MESSAGE 35 Multifunctional settings OPTION Menu With the OPTION menu, items shown in the table below can be performed. Select an item using the cursor buttons / on the projector or remote control, and press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table. Item Description Using the buttons / turns on/off the message function. TURN ON TURN OFF When the TURN ON is selected, detecting no signal automatically cycles through input ports in order of following. Then when an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state before the operation. RGB IN1 RGB IN2 COMPONENT VIDEO S-VIDEO VIDEO Using the buttons / adjusts the time to count down to automatically turn the projector off. 0 minute = DISABLE) AUTO OFF ENABLE AUTO OFF DISABLE 0 1 MENU [RGB] PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU SEARCH AUTO OFF LAMP TIME FILTER TIME SERVICE :SELECT TURN ON 0 0 0 SEARCH AUTO OFF When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with a no-signal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. RESET CANCEL · Please reset the lamp time only when you have replaced the lamp, for correct messages about the lamp. [. . . ] · If the indicators or a message prompts you to replace the lamp (see the "User's Manual - Operating Guide"), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage. 8 Lamp (continued) When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. To prepare a new lamp, contact your dealer and tell the lamp type number = DT00671. [. . . ]