User manual HITACHI CP-RS55

[. . . ] When the projector is installed bottom up, please use the accessory filter cover for bottom-up use. 1. Usual filter cover 2. Air filter 3. Claws Rail Air filter Filter cover for bottom-up use 4. Filter cover for bottom-up use Tabs 2 Arrangement Arrangement WARNING Install the projector in a suitable environment according to instuctions of the "User's Manual - Safety Guide". Put nothing that is sucked or sticks to the bottom of projector. (b) Refer to the illustrations and tables below to determine the screen size and projection distance. The values shown in the table are calculated (±3%) for a full size screen: 800x600 (c) up (c) down ENGLISH At 4:3 screen (a) Screen size [inch (m)] 4:3 (a) 40 50 60 70 80 90 100 120 150 200 (1. 0) (1. 3) (1. 5) (1. 8) (2. 0) (2. 3) (2. 5) (3. 0) (3. 8) (5. 1) (b) Projection distance [m (inch)] 1. 5 1. 8 2. 2 2. 6 2. 9 3. 3 3. 7 4. 4 5. 5 7. 4 (57) (72) (87) (101) (116) (130) (145) (174) (218) (291) (c) Screen height [cm (inch)] down up 8. 7 10. 9 13. 1 15. 2 17. 4 19. 6 21. 8 26. 1 32. 7 43. 5 (3) (4) (5) (6) (7) (8) (9) (10) (13) (17) 52. 3 65. 3 78. 4 91. 4 104. 5 117. 6 130. 6 156. 8 195. 9 261. 3 (21) (26) (31) (36) (41) (46) (51) (62) (77) (103) At 16:9 screen (a) Screen size [inch (m)] 16:9 (a) 40 50 60 70 80 90 100 120 150 200 (1. 0) (1. 3) (1. 5) (1. 8) (2. 0) (2. 3) (2. 5) (3. 0) (3. 8) (5. 1) (b) Projection distance [m (inch)] 1. 6 2. 0 2. 4 2. 8 3. 2 3. 6 4. 0 4. 8 6. 0 8. 1 (63) (78) (94) (110) (126) (142) (158) (190) (238) (317) (c) Screen height [cm (inch)] down up 1. 2 1. 5 1. 8 2. 1 2. 4 2. 7 3. 0 3. 6 4. 4 5. 9 (0) (1) (1) (1) (1) (1) (1) (1) (2) (2) 48. 6 60. 8 72. 9 85. 1 97. 2 109. 4 121. 6 145. 9 182. 3 243. 1 (19) (24) (29) (34) (38) (43) (48) (57) (72) (96) 3 Adjusting the projector's elevator / Connecting your devices Adjusting the projector's elevator WARNING Do not adjust the projector's elevator during use or immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector. [. . . ] After making sure that the power indicator lights to solid orange, set the power switch to the OFF position. · When a power supply is shut off with a power failure or the restart switch, before turning on again, make the projector cool down at least 10 minutes without operating. CONTROL RGB S-VIDEO VIDEO AUDIO K on the projector or remote control. Press the STANDBY/ON buttonappear on the screen for approximately 5 The message "Power off?" will seconds. Power off? STANDBY/ON 2. button on the projector or remote control again while the message The projector lamp will go off, and the POWER indicator will begin blinking orange. Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete. POWER (Blinking orange) POWER (Solid orange) indicator lights to solid 3. Make sure that the powerPOWER indicator will goorange, set the power switch to the OFF position. Do not set the power switch to the OFF position while the POWER indicator is green or blinking. POWER (Solid orange) lens For 4. usedsafety purposes, disconnect the power cord if the projector to be for prolonged periods of time. 9 ENGLISH Maintenance Maintenance Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. · Handle with care: jolting or scratching could cause the lamp bulb to burst during use. · If the indicators or a message prompts you to replace the lamp (see the "User's Manual - Operating Guide"), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage. 10 Maintenance Lamp (continued) When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. To prepare a new lamp, contact your dealer and tell the lamp type number = DT00701. If the projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to replace the lamp. 1. 2. In the case of replacement by yourself, After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing up. Please unhook the claws of the lamp cover using a minus screwdriver or similar, and remove the lamp cover. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles. Claws of lamp cover Insert the new lamp, and retighten firmly two screws that are loosened in the previous process to lock it in place. Interlocking the 2 tabs of the lamp cover to the projector, Screws marked position the lamp cover on the by arrow projector. point Slowly turn the projector so that the top of claws is facing up. [. . . ] Windows®: CD-ROM includes installer of Acrobat Reader 5. 1 English version. Clicking "for Windows" on the screen starts installer program. Click the model name of your projector first, and then click language you want from the displayed list. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. [. . . ]