User manual HITACHI CMP5000WXU

[. . . ] Color Plasma Display Monitor Model CMP5000WXU CMP5000WXJ USER'S MANUAL MANUEL UTILISATEUR READ THE INSTRUCTIONS INSIDE CAREFULLY. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. or Canada, please use and refer to the instructions written in either English or French. For customers in Japan, please use and refer to the instructions written in Japanese. [. . . ] Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer's intentions. During personal computer signal input 1 DOT BY DOT The input signal and the screen maintain a dot to line ratio of 1:1 and is thus highly faithful to the source. A 640 dots 1280 dots (Illustration shows 640 x 480 input. ) 480 lines 768 lines Changing the screen size The size of the picture or the picture's range projected on the screen can be changed between 4 screen sizes described in the table on this page. Press SCREEN SIZE to select the size. The screen size changes each time SCREEN SIZE is pressed as follows. 3 DOT BY DOT PARTIAL 2 3 4:3 FULL 2 2 4:3 The display fills the screen as much as possible without altering the aspect ratio of the input signal. Consult the table Computer Signal Formats Supported (page 31) for information regarding screen sizes supported by each signal format. Notes ÷ When the PARTIAL or FULL setting is used to display a nonwide screen 4:3 picture fully on a wide screen, a portion of the picture may be cut off or appear deformed. 3 FULL The display is presented with a widescreen aspect ratio of 16:9 and fills the entire screen. Operations ÷ Be aware that when the display is used for commercial or public viewing purposes, selecting the PARTIAL or FULL mode settings may violate the rights of authors protected under copyright law. ÷ When DOT BY DOT or 4:3 screen sizes are selected, the display position is moved slightly each time the power is turned on, in order to prevent image burning. Moving the screen position upward or downward During personal computer input (1280 x 1024/60Hz only), even when the PARTIAL setting is selected, the position of the screen can be adjusted by using 5/. The adjustment value will not, however, be stored in memory. 4 PARTIAL The PARTIAL setting is available only during personal computer input (1280 x 1024/60 Hz only). However, in order to maintain the 1:1 ratio, a portion of the display will not appear on the screen. A A 768 lines 1024 lines Use 5/ to adjust the position of the video image on the screen. 18 En Operations Press SET to select the zoom ratio. Pressing SET repeatedly changes the zoom ratio in the following order: 3 x 1. 5 x 4. 0 2 3 x 2. 0 x 3. 0 2 Partial Image Enlargement (POINT ZOOM) This display allows any one of nine screen areas (AREA 1 to AREA 9) to be selected and enlarged to x1. 5, x2, x3, or x4. When performing point zoom enlargement, the direction buttons (5//2/3) can be used to move the enlarged portion up-down and right-left. 1 Press the remote control unit's POINT ZOOM. ÷ When the zoom ratio is changed, the screen image is enlarged based on the screen center. ÷ 5//2/3 can be used to move the enlarged portion up-down and right-left. ÷ If no operation is undertaken for three seconds or more, the display screen will disappear. SET or 5//2/3 can be pressed again if desired to change the zoom ratio or display position. 4 SELECT P. ZOOM SET EXIT ZOOM Press the remote control unit's POINT ZOOM once again to cancel the point zoom operation. The point zoom function will also be canceled whenever the input signal changes, the menu screen is displayed, or the INPUT changes. Note 2 Press 5//2/3 as required to select the desired screen area (AREA 1 to AREA 9). AREA 1 display range AREA 2 display range Whenever point zoom is selected, the screen size automatically changes to FULL. AREA 3 display range AREA 1 x 4. 0 x 2. 0 x 1. 5 x 2. 0 x 1. 5 x 2. 0 x 1. 5 AREA 4 display range AREA 5 display range AREA 6 display range AREA 4 x 4. 0 x 2. 0 x 1. 5 x 3. 0 AREA 5 x 4. 0 x 2. 0 x 1. 5 x 3. 0 x 3. 0 AREA 6 x 4. 0 x 2. 0 x 1. 5 AREA 7 display range AREA 8 display range AREA 9 display range AREA 7 x 4. 0 x 2. 0 x 1. 5 x 3. 0 AREA 8 x 4. 0 x 2. 0 x 1. 5 x 3. 0 x 3. 0 AREA 9 x 4. 0 x 2. 0 x 1. 5 19 En Operations x 3. 0 AREA 2 x 4. 0 x 3. 0 x 3. 0 AREA 3 x 4. 0 English 3 Operations English Automatic Power OFF This display is equipped with automatic powermanagement and auto-power-off functions, which allow the unit to automatically switch to power-saving mode when no sync signal is detected. (A warning message appears onscreen before these functions operate. ) Notes ÷ The Power Management function can be set only when the INPUT 1 signal is selected. ÷ The automatic power-off function can be set only when the INPUT 2 signal is selected. ÷ Always turn off the plasma display's main power switch when not using the display for extended periods of time. 3 Press 5/ to select either the POWER MANAGEMENT or AUTO POWER OFF mode. [When using INPUT 1] MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA SELECT SET CHANGE MENU EXIT [When using INPUT 2] 1 Press MENU to display the menu screen. MAIN MENU SCREEN : CO NT RA S T 0 : BR I GHT . E NH AN CE 0 RE S E T PICTURE SET UP INPUT1 OPTION MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L A U T O P OWE R O F F C L AMP P O S I T I O N SETT I NG INPUT2 OPTION : I N P UT 2 : OF F : AU T O : V GA 4 Press SET to confirm selection of the POWER MANAGEMENT or AUTO POWER OFF. 3 OFF ON 2 SELECT SET ENTER MENU EXIT 2 Operations Press 2/3 to select SET UP. [When using INPUT 1] MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA ÷ When OFF is selected, the display will continue in operating mode, regardless of the presence/ absence of an input sync signal. ÷ When POWER MANAGEMENT: ON is selected, if a sync signal is not detected, a warning message is displayed for 8 seconds, after which the display automatically enters the power-saving mode (*1) and the STANDBY/ON indicator flashes green. If a sync signal (*2) is input again later, the plasma display automatically returns to normal operating mode. *1. Except when input signal is G on SYNC or composite SYNC SELECT SET ENTER MENU EXIT [When using INPUT 2] MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L A U T O P OWE R O F F C L AMP P O S I T I O N SETT I NG INPUT2 OPTION : I N P UT 2 : OF F : AU T O : V GA ÷ When AUTO POWER OFF: ON is selected, if no sync signal is detected for 8 minutes or more, a warning message will be displayed for 30 seconds, after which the unit's power will switch to STANDBY mode. 5 When the setup is finished, press MENU to exit the menu screen. Note The POWER MANAGEMENT and AUTO POWER OFF functions must be set individually for each input (INPUT 1 or INPUT 2). To return to operating mode: ÷ To return to normal operation from POWER MANAGEMENT mode: either operate the computer, or press INPUT on the display or remote control unit. ÷ To return to normal operation from AUTO POWER OFF mode: Press STANDBY/ON on the display or remote control unit. SELECT SET ENTER MENU EXIT 20 En Display Panel Adjustments Adjusting the Picture Quality 1 Press MENU to display the menu screen. MAIN MENU SCREEN : CO NT RA S T 0 : BR I GHT . E NH AN CE 0 RE S E T PICTURE SET UP INPUT1 OPTION PICTURE mode adjustment items Below are brief descriptions of the options that can be set in the PICTURE mode. [. . . ] 2 Install the mounting fittings with bolts at the positions shown in the figure on the left. Hexagon socket head screw Flat countersunk head screw For bottom 1. Check the indications LEFT and RIGHT at the rear of the speakers, observe the indication "UP ", and fasten the upper mounting fitting provisionally to the display. Adjust the position so that the gap between the speaker and the display is uniform, and then tighten the screws firmly. 47 En CONNECTION TO A Plasma Display 1. [. . . ]