User manual HITACHI CMP4221U

[. . . ] CMP4221 USER'S MANUAL Thank you very much for purchasing the HITACHI Plasma Display Monitor. Before using your monitor, please carefully read the "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to operate the monitor properly. You will find it useful in the future. Notes on lnstallation Work: This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. [. . . ] When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains. ATTENTION Do not drop or impact the remote control. . Do not splash the remote control with water or put it on a wet object. Before leaving the remote control out of use for an extended period of time, remove the batteries from it. If the remote control begins to lack responsiveness, replace the batteries. Strong light, such as direct sunlight, shining on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light. 11 ENGLISH INSTALLATION INSTRUCTIONS Installation the Desktop stand (option) · If you have purchased the model without the stand attached: When installing the monitor, use the optional Desktop stand. The Desktop stand has been used for the illustrations in this manual. WARNING Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage caused by use of other mount units or improper installation. CAUTION Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this by our self. In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches: For a desktop set- up) or more between the sides and other objects such as walls, etc. , so that the ventilation holes are not blocked. (*) 10cm (4 inches) or more* Clamp Cord or chain Anti-tumble measures CAUTION Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury. Securing to a wall or pillar Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar. Hook Chain cord or chain Wall or Pillar Clamp Securing desktop 1) Using wood screws (two) fasten the set to the clamping screw holes on the rear of the stand as shown. 2) Using commercially available wood screws, secure the set firmly in position. Wood Two places Mounting the Speaker Unit (option) Refer to the instruction manual concerning mounting of the optional speaker unit. 12 ENGLISH INSTALLATION INSTRUCTIONS (continued) Read SAFETY INSTRUCTIONS ( 2 to 9 ) carefully to ensure maximum safety before proceeding to these steps: Choose an appropriate site and install the product on a level table where the stand is secure. Install the monitor to have ready access to a power socket available. Make sure that the power switch of this device is turned off. Connecting to Video Imaging Device device. See "Product Specifications" concerning the specifications of this device. 35 ~ 37 (2) Make sure that the power switch of the monitor is turned off. (3) Make sure that the power switch of the imaging device is turned off. (4) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this device and the signal output terminal of the imaging device. * Cable shown are not supplied with the monitor and are available locally where ever consumer electronic product are sold. CAMCORDER Monitor rear panel Speaker(R) Speaker(L) DVD PLAYER SPEAKER TERMINAL (6 ) 10W Power Code SPEAKER TERMINAL (6 ) 10W Basic Connection Set-TopBox Better Connection VCR [An example of connecting video components] If the AV OUT terminal is connected to a 2nd monitor, it is possible to view the same image as on the main source. The composite video signal from AV1, AV2 input will be displayed on both screens at the same time. If video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer vedio quality. Applicable signals for each input terminal Applicable Signal Terminal AV1 AV2 AV3 AV4 RGB HDMI RCA S-video Composite (See PRODUCT SPECIFICATIONS for details, 35 ) RCA Component D-sub HDMI RGB (O: Available) 13 ENGLISH (1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this Connecting to a PC or a HDMI device Con (1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this device. See "Product Specifications" concerning the specifications of this device. 35 ~ 37 (2) Make sure that the power switch of the personal computer or the DVD player is turned off. (3) Connect the signal input terminal (RGB) or HDMI on the rear panel of this device. Use a cable that fits the input terminal of this device and the output terminal of the personal computer. Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the personal computer manufacturer or your local retail dealer. Monitor rear panel Speaker(R) Speaker (L) SPEAKER TERMINAL (6 )10W Power Cable Connector SPEAKER TERMINAL (6 )10W Power Cord 3. 5mm Stereo mini jack (D-Sub) (HDMI) 3. 5mm Stereo mini jack 1 To Audio Output To Audio Output PC DVD Player 1 In case of using analog audio, when connecting with DVI-HDMI transformation connector, use HDMI audio terminal for input. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. [. . . ] 8) Press the or buttons and search for clear characters over the entire screen. 9) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen. The display image may be momentarily disturbed during clock adjustment but this is not a failure. Symptom 2 Example Text displayed across the screen appears blurred in its entirety (Figure 2). Figure 2 Before adjustment Figure 3 Before adjustment After adjustment After adjustment Adjustment procedure 1) Press the MENU button. [. . . ]