User manual HITACHI CM753ET

[. . . ] COLOUR MONITOR CM751 ET CM752ET CM753ET with USER MANUAL. . . . . I BEDIENUNGSANLEITUNG. . . 59 EasyMenu ! EasyMenu is HITACHI's On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR@ compliant when used with a computer equipped with VESA DPMS. [. . . ] Instructions to Users : This equipment complies with the requirements of FCC (Federal Communication Commission) equipments provided that following conditions are met. (2) Video inputs : The input signal amplitude must not exceed the specified level. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity According to 47CFR. Part 2 and 15 for Class B Personal Computers and Peripherals; and I or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: Nissei Sanevo America, Ltd. 02090- 1124 U. S. A. Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 5 2. 909. Green & Yellow to Earth Brown to Live Fuse Blue to Neutral Cord Clamp As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol @ or coloured GREEN or GREEN and YELLOW. The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED. Install the monitor in the following way, taking care to maintain safety. Installation Install the monitor on a horizontal base. Front Cover CRT Surface Connector Power Switch Control Panel Tilt & Swivel Base FRONT VIEW , j! REAR VIEW / Signal Input Connector Signal Cable / to the host computer 2. Power Cord Connection @ Make sure of using the power cord meeting the safety standard of the country in which you are using the monitor. @ Insert the connector of a power cord to the AC Inlet of the monitor. @I Insert the plug of the power cord to a receptacle of the correct voltage. Signal Cable Connection (iJ Insert the connector of a signal cable to the Signal Input Connector of the monitor, with attention to the suitability, and secure the screws on the connector shell firmly. @ Connect the another connector of the signal cable to the host computer. AC Inlet A receptacle of the correct voltage \ `4 Power COI rd \ 6 l Use a signal cable with the D-Sub Mini 15pin Connector. 3 l If the graphics board supplies more than one type of sync. signal type will be automatically selected by the monitor, with the priority shown in the following table. 4. Power On Turn on the Power Switch of the monitor first, then the computer. Paae 9 "POWER ON/OFF" Refer to NOTICE : n After turning OFF the switch, wait at least 5 seconds to restart the monitor. n If the picture doesn't appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds to restart the monitor. Make sure the power switch of the computer, power cord connection, signal cable connection and the input sync. W If the colour is impure on the screen after turning ON the monitor, wait for about 10 minutes and press the DEGAUSS button. Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. [. . . ] n If your store is at its maximum already, storing a setting for a new video mode overwrites the oldest user setting. n The video mode is distinguished by the horizontal/vertical frequency and polarity of the horizontal/vertical sync. When the video modes are almost similar in these factors however, the video modes may not be discriminated as different. . YOU Restoring Condition When the monitor detects the same video mode. Colour Balance (Red, Green, Blue) j Rotation Contrast Brightness Colour Select Language Select When the colour balance "No . 4USER" is . [. . . ]