User manual HITACHI AVC01U

[. . . ] Audio Video Center This Audio Video Center is intended to be use with Hitachi Ultra Thin monitors that includes remote controls. - (2) Composite Video Inputs, (2) Component Video Inputs. Operating Guide Model Name AVC01U READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. Record the serial number of your A/V Center for future reference. SERIAL NO. This serial number is located on the bottom side of the unit ANY QUESTION ABOUT THIS PRODUCT PLEASE CONTACT 800-HITACHI CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Hold down the device button (DVD, PVR/VCR, SAT/CBL or AVR) on the remote and enter the four digit preset code that matches your device as shown on pages 23 ~ 24 . If done correctly, the device LED indicator will blink 3 times to confirm proper setup. The remote will now control the desired device. Power button Device buttons Numeric buttons 4. Select Cable mode by using your SAT/CBL button to position the LED indicator on SAT/CBL. Hold down the SAT/CBL button on the remote and press the numbers 0, 0, 0 and 3. The remote will turn off your cable box when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different four digit preset code. The remote will now control your Cable box. Remote Control Backlight Feature When you press any remote control button, the buttons will light up. The buttons will appear to light if the room is dark. 7. Repeat the same procedure for your set-top-box or satellite receiver (select SAT/CBL), your DVD (select DVD), your VCR/PVR(select VCR/PVR), or your AVR (select AVR). NOTE Disabling Remote Control Backlight Feature 1. To re-enable the backlight feature do steps 1~3 again (these steps toggle the Backlight Feature on and off, default is ON). If your external device cannot be operated after performing the above procedures, your external device code has not been precoded into the remote. In the unlikely event that your external device cannot be operated after performing the above procedures, please consult your external device operating guide. The remote control will remember the codes you have programmed even after the batteries are removed from the remote control. To reset all programmed codes to factory default place remote control in TV mode, then press and hold TV mode key and enter "9", "8", "1" in sequence. Depending of your UT Monitor model your remote control could have or not Backlight function. 19 SETUP OPERATION (continued) ENGLISH 20 How to Use the Remote to Control your External Devices Cable Device Button Set-Top-Box/ Satellite Receiver Device Button MY CABLE BOX CODE IS:____________________ NOTE MY SET-TOP-BOX/SATELLITE RECEIVER CODE IS:____________________ NOTE Refer to the operating guide of the Cable Box for operation of the buttons exclusively for the Cable Box. PRECODED CABLE BOX buttons Refer to the operating guide of the Set-Top-Box/Satellite Receiver for operation of the buttons exclusively for the Set-Top-Box/Satellite Receiver. PRECODED SET-TOP-BOX/SATELLITE buttons These buttons transmit the chosen precoded STB/Satellite codes : -Power -Cursor & OK -Number PAD -Menu -Info -Enter -Return -Channel Up & Down -Fav CH -Guide -Dash(-) -Color Buttons -Last CH These buttons transmit the chosen precoded cable codes : -Power -Cursor & OK -Number PAD -Menu -Info -Enter -Return -Channel Up & Down -Fav CH -Guide -Dash(-) -Color Buttons -Last CH EXCLUSIVE TV mode (Monitor) buttons These buttons are for operating the TV : -Input -P. Mode -HDMI -Aspect -Vol Up & Down -RGB -Mute EXCLUSIVE TV mode (Monitor) buttons These buttons are for operating the TV : -Input -P. Mode -HDMI -Aspect -Vol Up & Down -RGB -Mute SETUP OPERATION (continued) How to Use the Remote to Control your External Devices DVD Device Button VCR/PVR Device Button MY DVD PLAYER CODE IS:___________________ NOTE MY VCR/PVR CODE IS:____________________ NOTE Refer to the operating guide of the DVD Player for operation of the buttons exclusively for the DVD Player. PRECODED DVD buttons Refer to the operating guide of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR. PRECODED VCR/PVR buttons These buttons transmit the chosen precoded VCR/PVR codes : -Power -Cursor & OK -Record -Menu -Channel Up & Down -Play, Stop, Pause, RWD, -Return -Number PAD FWD, Skip -Info -Last CH (FWD, RWD) -Guide -FAV CH These buttons transmit the chosen precoded DVD codes : -Play, Stop, Pause, -Power -Cursor & OK RWD, FWD, Skip -Menu -Info RWD, Skip FWD, Rec -Return -Number PAD -Guide -Dash(-) -Enter EXCLUSIVE TV mode (Monitor) buttons These buttons are for operating the TV : -Input -P. [. . . ] You understand and agree that your use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys' fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement. The Software is protected by federal copyright laws, international copyright treaties and other intellectual property laws and treaties. [. . . ]