User manual HITACHI 65S500

[. . . ] PROJECTION COLOR TV 51S500 57S500 65S500 OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-18 THE REMOTE CONTROL 19-36 Video Audio Aspect Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 37-63 Sel USEFUL INFORMATION INDEX 64-70 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. [. . . ] Press and release the Cable (CBL) button to switch to Cable pre-coded mode. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 36. The remote will turn off your cable box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code. The remote will now control your Cable box. TV POWER 5. 6. THE REMOTE CONTROL NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. The LAST CH button will act as the cable box ENTER button if required. VCR CBL STB SOURCE WIZARD CD DVD PVR AMP 1 4 7 2 5 8 0 3 6 9 SLEEP INFO ANT C. C. PHOTO ASPECT VIRT UAL HD 3. ME NU EX IT VOL SELECT CH 4. MUT E CH LAST VID 5 VID 1 VID 5. The SLEEP button will act as your cable box `100' button if required. CABLE (CBL) button This button allows the remote to control your cable box by setting it to CABLE mode. PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. EXCLUSIVE TV buttons These buttons are for operating the TV. 2 VID 3 VID 4 PIP SURF FREEZE PIP MODE PIP ACCESS SWAP DAY/NIGHT 6. REC MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 31 USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to page 36). Aim the remote control at the front of your set-top-box/satellite systems. Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode. Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as shown on page 36. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your settop-box/satellite receiver. [. . . ] Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. · GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. [. . . ]