User manual HITACHI 57T600

[. . . ] PROJECTION COLOR TV 57T600 OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-23 THE REMOTE CONTROL 24-42 Video Audio Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 43-71 Sel USEFUL INFORMATION INDEX 72-79 IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television. [. . . ] Press the PIP button and then press the FREEZE button to freeze the sub-picture. Press the FREEZE button again and press the PIP button to return to normal viewing. THE REMOTE CONTROL Hot Springs Clay Mask C/O John Doe Run-Spa Retreat P. O. Box 55512 Any Town, USA 98765 Check or Money Order Only 1-800-555-1212 Ant A 10 FREEZE FREEZE Hot Springs Clay Mask C/O John Doe Run-Spa Retreat P. O. Box 55512 Any Town, USA 98765 Check or Money Order Only 1-800-555-1212 SPLIT FREEZE(with PIP OFF) PIP FREEZE should be in SPLIT mode. Press the FREEZE button to freeze the picture you are currently viewing (only the right sub-picture will freeze). Press the FREEZE button again to return to normal viewing. Main Picture Sub Picture Ant A 12 FREEZE FREEZE STROBE FREEZE(with PIP OFF) PIP FREEZE should be in STROBE mode. Press the FREEZE button to freeze three frames of the picture you are currently viewing. This feature is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing. FREEZE FREEZE NOTES: 1. When in ANT A/ANT B, the FREEZE mode cycles through POP-POP-SPLIT-STROBE. When in ANT C, the FREEZE mode cycle will depend upon the signal format received. 35 USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. You must first program the remote to match the remote system of your VCR (refer to page 42 for pre-codes). Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 42. The remote will turn off your VCR when the correct two digit preset code is entered. The remote will now control your VCR. POWER 5. 6. TV VCR CBL STB SOURCE WIZARD DVD CD TAPE AMP NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR's code has not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. VCR Button This button allows the remote to control your VCR by setting it to VCR mode. PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program. EXCLUSIVE TV Buttons These buttons are for operating the TV. THE REMOTE CONTROL NT D ME NU EX IT CH SV CS VID HD SC VID 5 1 VID 2 VID 3 VID 4 PIP ACCESS REC MY VCR CODE IS: NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 36 USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. [. . . ] Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. · RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. · BLOCK NOISE (Ant C Input): Fuzzy blocks may appear in some area or the whole area of the screen. This is usually caused by interference from automobile ignition systems, neon lamps, electrical drills, ghosting of the image and weak signals. NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from the TV set to a considerable distance. 73 USEFUL INFO SYMPTOMS No Picture, no sound © Sound OK, picture poor © Picture OK, sound poor © Picture blurred © Lines or streaks in picture Poor reception on some channels Picture rolls vertically No color © Poor color © ©© HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. [. . . ]