User manual HITACHI 50UX52B

[. . . ] Home Electronics Division may void the user s warranty. POWER SOURCE This projection television is designed to operate on 120 volts 60Hz, AC current. TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE. NOTE: This television receiver will display television closed captioning, ( paragraph 15. 119 of the FCC rules. CC or ), in accordance with CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other hazards. If the television does not operate properly, unplug the television and call your authorized dealer or service shop. 2 SAFETY TIPS IMPORTANT SAFEGUARDS CAUTION: ¥ Read all of these instructions. [. . . ] INPUT button The INPUT button will select between antenna signal and the two sets of video input jacks each time the button is pressed. If the Picture-in-Picture is on, the INPUT button will select between the two sets of video input jacks and antenna source when main channel is chosen with the PIP CH button. If the sub-picture is chosen, the INPUT button will select between the two sets of video input jacks and the source COMPONENT VIDEO: Y-CBCR INPUT 2 source will be displayed as a blank PIP sub-picture. ANT A 28 INPUT S - IN: 1 INPUT Y - CBCR: 2 INPUT 21 PICTURE-IN-PICTURE (PIP) Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna input on both the main picture and sub-picture simultaneously, with separate tuning control for each. ANTENNA input can be viewed as both the main picture and the sub-picture simultaneously. COMPONENT VIDEO: Y-CBCR INPUT 2 sources can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. Every press of the PIP CH will highlight the main or sub-picture source. The top channel display is the main picture and the bottom display is the sub-picture. The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the ANTENNA source or any of the video inputs. S-VIDEO VIDEO POWER (MONO)/L TV HELP CABLE PIP CH SWAP MOVE VCR TV/VCR FRZ R PIP AUDIO INPUT 1 TV INPUT TERMINAL REC STOP PAUSE , S- S VH V L R O U TPU T BAC K O F VC R MENU VOL EXIT RECALL HI TAC H IM odel orsi iarm odel ml LST-CH CH PIP button Press the PIP button and a sub-picture appears in one corner of the screen. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. If your VCR does not have a power function, the remote will issue the CHANNEL UP function. * POWER TV HELP PIP CABLE PIP CH SWAP MOVE VCR TV/VCR FRZ REC STOP PAUSE MENU VOL EXIT RECALL LST-CH CH MUTE LIGHT 1 VCR Button This button allows the remote to control your VCR by setting it to VCR mode. PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program. EXCLUSIVE TV Buttons These buttons are for operating the TV. 2 5 8 0 3 6 9 SLEEP 4 7 INPUT CLU-436UI NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 25 USING THE REMOTE TO CONTROL CABLE BOX/SATELLITE FUNCTIONS Operating the precoded function for your cable box. You must first program the remote to match the remote system in your cable box. Hold down the CABLE button on the remote, enter the two digit preset code that matched your cable box as shown on page 27. The remote will turn off your cable box when the correct two digit preset code is entered. [. . . ] Press the RECALL button again to display the SPECIAL EVENT REMINDER message. 52 INFO CALENDAR INFO Use this function to check the day, month, and year. Dates programmed in SPECIAL EVENT REMINDER will appear blinking and special event message will be displayed. SET UP CUSTOM VIDEO AUDIO THEATER INFO SET UP CUSTOM VIDEO AUDIO THEATER INFO SPECIAL EVENT REMINDER CALENDAR CURSOR CALENDAR S 5 12 19 26 M MAR 2000 TWTF 1 23 678 9 10 13 14 15 16 17 20 21 22 23 24 27 28 29 30 31 S 4 11 18 25 MENU TO MENU BAR TO QUIT EXIT MENU TO MENU BAR TO QUIT EXIT Press CURSOR or to change the month. If the clock is not set, you can not use this function and the next screen will appear. SET UP CUSTOM VIDEO AUDIO THEATER INFO CALENDAR PLEASE SET CLOCK FIRST MENU TO MENU BAR TO QUIT EXIT NOTE: 1. Special event message will be displayed only if current date is within the day of Start Reminder Specifications as chosen in SPECIAL EVENT REMINDER (see page 52). [. . . ]