User manual HITACHI 50UX19K

[. . . ] IMPORTANT 1 HITACHI PROJECTION COLOR TV 60SX8B/9K 50SX6P 50UX18B/19K 46UX16B/17K OPERATING GUIDE TABLE OF CONTENTS IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY TIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PICTURE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Sub-Picture will not appear while a FAVORITE CHANNEL is being selected. The Sub-Picture will reappear after the FAVORITE CHANNEL display is gone. Each strobe freeze frame is delayed about 0. 1 (1/10) second. 28 USING THE REMOTE TO CONTROL VCR FUNCTIONS USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the pre-coded function for your VCR This Genius Remote is designed to operate different types of VCRs. You must first program the Genius Remote to match the remote system in your VCR. Set the USE/LEARN mode select switch on the rear side of the Genius Remote to "USE. " 3. While holding down the SELECT button, press the button that matches your VCR as shown on page 25. The channels of the VCR will begin changing when the correct button is pressed. When this occurs, the Genius Remote Control is programmed for your VCR. If the VCR channels do not change after 5 seconds, try a different Genius Remote button. If your VCR cannot be operated after performing the above procedures, this means that your VCR's codes have not been precoded into the GENIUS REMOTE. The GENIUS REMOTE CONTROL will remember the codes you have programmed in until the batteries are removed from the GENIUS REMOTE CONTROL. After replacing the batteries repeat the entire programming procedure stated above. If you have a play back only VCR (no CH UP/DOWN function), please follow operating step 5 described above and then check a VCR function until you find the button that will allow the precoded VCR buttons to operate your VCR. PRECODED VCR BUTTONS These buttons always transmit the chosen precoded VCR codes. SELECT BUTTON This is for setting up the Genius Remote to transmit the VCR's remote codes. EXCLUSIVE TV BUTTONS These buttons are for operating the TV. 29 USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the pre-coded function for your Cable Box This Genius Remote is designed to operate different types of cable boxes. You must first program the Genius Remote to match the remote system in your cable box. While holding down the SELECT button, press the button that matches our cable box as shown on page 25. The channels of the cable box will begin changing when the correct button is pressed. When this occurs, the Genius Remote Control is programmed for your cable box. If the cable box channels do not change after 5 seconds, try a different Genius Remote button. If your cable box cannot be operated after performing the above procedures, this means that your cable box codes have not been precoded into the GENIUS REMOTE. [. . . ] Screens that have been cleaned with anything other than water and a mild soap solution. Lenses from units that have been sold or transferred from the original purchaser. Any lens element that is permanently attached to the CRT assembly is excluded from the lifetime warranty. The labor to repair or replace will be at no charge during the one year warranty duration. [. . . ]