User manual HITACHI 50SBX70B

[. . . ] This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model. Follow all warnings and instructions marked on this color television. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION TO RAIN OR MOISTURE. NOTE: · There are no user serviceable parts inside the color television. [. . . ] After replacing the batteries repeat the entire programming procedure as stated above. The INPUT button will act as your VCR `100' button if required. NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 25 USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD Player. You must first program the remote to match the remote system of your DVD Player. Hold down the DVD/VCR button on the remote, enter the two digit preset code that matches your DVD Player as shown on page 28. The remote will turn off your DVD Player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD Player. If the DVD Player does not turn off after five seconds, try a different two digit preset code. The remote will now control your DVD Player. POWER TV CBL/SAT SWAP DVD/VCR PIP HELP MOVE FREEZE DVD button This button allows the remote to control your DVD Player by setting it to DVD mode. PIP CH MENU SELECT MUTE EXIT LAST CH EXCLUSIVE TV buttons These buttons are for operating the TV. VOL CH 1 4 7 INPUT 2 5 8 0 3 6 9 STATUS PRECODED DVD buttons These buttons always transmit the chosen precoded DVD codes. When the remote is in DVD mode, EXIT button is used as ENTER button. REC TV/VCR PIX NOTES: 1. If your DVD Player cannot be operated after performing the above procedures, your DVD Player's code has not been precoded into the remote. In the unlikely event that your DVD Player cannot be operated after performing the above procedures, please consult your DVD Player operating guide. Use the CURSOR function desired. or on the remote to highlight the SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER MENU M e n u L anguage Sig n a l Source Au to Channel Set Ch a n n e l Memory Ch a n n e l Li st Clo ck Set Dig ita l Array Menu To M e n u B a r To Q u i t Exit NOTE: To see an auto-demonstration of the on-screen displays with HELP text displayed, press and hold the POWER button on the TV set for approximately five seconds. Press the EXIT button to end the auto-demonstration. MENU LANGUAGE This feature will allow you to select any one of three different languages for all on-screen displays. SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER SEL SETUP CUSTOMIZE VIDEO AUDIO THEATER Cursor Menu Language Sig n a l So u r ce Au to Ch a n n e l Se t Ch a n n e l M e m o r y Ch a n n e l L ist Clo ck Se t Dig ita l Ar r a y English Francai s E spañol C ursor Menu Language S i gnal Source A uto C hannel Set C hannel Memory C hannel Li st C l ock Set D i gi tal A rray English Franc ai s E sp añol Menu To M e n u B a r To Q u i t Exit Menu To M e n u B a r To Q u i t Exit Use CURSOR or to select the MENU LANGUAGE of your choice. Press EXIT to quit menu or CURSOR to return to previous menu. 31 SETUP SET UP SIGNAL SOURCE Select ANTENNA if you are using an indoor or outdoor antenna. Select CATV if you have cable TV. SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER M e n u L anguage Sig n a l Source Au to Channel Set Ch a n n e l Memory Ch a n n e l Li st Clo ck Set Dig ita l Array A ntenna C atv 1 C atv 2 C ursor Menu To M e n u B a r To Q u i t Exit SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER SEL SETUP CUSTOMIZE VIDEO AUDIO THEATER Menu Language S i g n a l S o urc e A u t o C h a n ne l Se t C h a n n e l M em o r y C h a n n e l L ist Clock Set Digital Array An t e n n a Ca tv 1 Ca tv 2 C ursor Menu Language S ignal Source A uto C hannel Set C hannel Memory C hannel Li st C l ock Set D i gi tal A rray A ntenna C atv 1 C atv 2 Menu To M e n u B a r To Q u i t Exit Menu To M e n u B a r To Q u i t Exit Press CURSOR or to highlight the signal source and press SELECT button to select the correct SIGNAL SOURCE mode. Press EXIT to quit MENU or CURSOR to return to previous menu. RECEPTION BAND CATV 1 OR CATV 2 AIR CATV CHANNEL VHF 2~13 VHF 2 ~ 13ch UHF 14 ~ 69ch Mid band A~1 A-5 ~ A-1 Super band J~W Hyper band W + 1 ~ W + 28 Ultraband W + 29 ~ W + 84 65 ~ 125 Indicated on the screen 2 ~ 13 14 ~ 22 95 ~ 99 23 ~ 36 37 ~ 64 Reception channels for each mode are shown at the left. Refer to your cable or TV guide for channel identification standards. If certain CATV channels are poor or not possible in CATV1 mode, set SIGNAL SOURCE to CATV2. 32 SETUP SET UP AUTO CHANNEL SET This feature will automatically store active TV channels in CHANNEL MEMORY. This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ). SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER M e n u L anguage Sig n a l Source Au t o Channel S et Ch a n n e l Memory Ch a n n e l Li st Clo ck Set Dig ita l A rray C ursor B egi n Menu To M e n u B a r To Q u i t Exit SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER SETUP CUSTOMIZE VIDEO AUDIO THEATER M e n u L a n g ua g e S i g n a l S o u rce A u t o C h a n ne l Se t C h a n n e l M em o r y C h a n n e l L i st Clock Set Digital Array A uto C hannel S et Be g in SELECT Instal l i ng C hannel 110 88% C ompl ete Menu To M e n u B a r To Q u i t Exit Menu To M e n u B a r To Q u i t Exit If the EXIT button is pressed while the AUTO CHANNEL SET function is engaged, programming will stop. Remember to select the correct SIGNAL SOURCE mode before using AUTO CHANNEL SET. See CHANNEL MEMORY to add or erase additional channels. 33 SETUP SET UP CHANNEL MEMORY Use this function after AUTO CHANNEL SET to add or erase additional channels to the remote control CHANNEL or buttons. SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER SEL SETUP CUSTOMIZE VIDEO AUDIO THEATER M e nu L a n g u a g e S i g n a l So u r ce A u t o Ch a n n e l Se t C h a n n e l M e mo ry C h a n n e l L ist C l o c k Se t D i g i ta l Ar r a y C ursor Ch a n n el 3 Ad d Er a se Menu Language S i gnal Source A uto C hannel Set C hannel Memory C hannel Li st C l ock Set D i gi tal A rray C hannel 3 A dd E rase N ext C h Ch Ch or # keys Menu To M e n u B a r To Q u i t Exit C ursor Menu To M e n u B a r To Q u i t Exit SETUP CUSTOMIZE VIDEO AUDIO THEATER SETUP CUSTOMIZE VIDEO AUDIO THEATER Menu Language S i g na l So u r ce A u t o Ch a n n e l Se t C h a nn e l M e mo ry C h a n n e l L ist C l o ck Se t D i g i ta l Ar r a y Ch a n n e l 3 Ad d Era se Ne xt Ch Ch Ch o r # ke ys SELECT Menu Language Si gnal Source Auto C hannel Set C hannel Memory C hannel Li st C l ock S et D i gi tal Array C hannel 3 A dd E rase N ext C h Ch Ch or # keys Menu To M e n u B a r To Q u i t Exit Menu To M e n u B a r To Q u i t Exit To add or erase additional channels while still in CHANNEL MEMORY use CHANNEL channel. Press EXIT to quit menu or CURSOR to return to previous menu. or , or the number buttons to change the 34 SETUP SET UP CHANNEL LIST This function allows you to review which channels are labeled in CHANNEL ID (ID. ), which have been added to CHANNEL MEMORY (SCAN), and which are protected by PARENTAL CONTROL (LOCK). SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER M e n u L anguage Sig n a l Source Au to Channel Set Ch a n n e l Memory Ch a n n el List Clo ck Set Dig ita l Array CURSOR Menu To M e n u B a r To Q u i t Exit SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER SEL SETUP CUSTOMIZE VIDEO AUDIO THEATER Channel List Ch Id 1 **** 2 **** 3 **** 4 **** 5 **** 6 **** 7 **** 8 **** An t Sc a n Lock ON ON --------------- CURSOR C hannel List Ch Id 9 **** 10 **** 11 **** 12 **** 13 **** 14 **** 15 **** 16 **** A nt S can ON -------- Lock ON -------- Menu To M e n u B a r To Q u i t Exit Menu To M e n u B a r To Q u i t Exit Press CURSOR or to review more channels. NOTE: Each touch of CURSOR or will display the next eight channels. 35 SETUP SET UP CLOCK SET The time must be set before you can use the 4 EVENT PROGRAM or TV TIME OUT. SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER M e n u Language Sig n a l S ource Au to Channel Set Ch a n n el Memory Ch a n n el Li st Clo c k Set Dig ita l Array CURSOR Menu To M e n u B a r To Q u i t Exit SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER SEL SETUP CUSTOMIZE VIDEO AUDIO THEATER Clock Set - - : - - AM Jan 01 2001 CURSOR C lock S et - - : - - A M Mar 01 2001 Menu To M e n u B a r To Q u i t Exit Menu To M e n u B a r To Q u i t Exit Use CURSOR or to set the time, date, and year. Press EXIT to quit menu or CURSOR to return to previous menu when the CURSOR is in the first position. 36 SETUP SET UP DIGITAL ARRAY Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. [. . . ] However, if RESET is selected, all modes will reset to the initial conditions as explained above. When RESET is selected, it will take approximately two seconds to return to factory conditions (SPORTS mode). Press EXIT to quit menu or CURSOR to return to previous menu. 54 CARE OF YOUR HITACHI PROJECTION TV AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a dry cloth. Place your television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your television will not be used for a long period of time, for instances, when you go on vacation. DO NOT Do not clean your screen or cabinet with strong cleaners, polishes or a chemically treated cloth. Do not place rubber or vinyl products or cellophane tape on your television. Do not touch the screen too often. Do not subject the remote control to shocks such as dropping it on the floor, etc. Physical damage to the precision parts may result. Avoid placing the remote control in a high humidity place or getting it wet. [. . . ]