User manual HITACHI 50EX12BX

[. . . ] IMPORTANT -1- HITACHI PROJECTION COLOR TV 50EX12BX 50EX13KX 50EX16B OPERATING GUIDE TABLE OF CONTENTS IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PICTURE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use this connection in place of the standard video connection if your device has this feature. If your device has only one audio output (mono sound), connect it to the left audio jack on the TV. Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 1 in the example on p. Refer to your VCR operating guide for more information on "line" input-output connections. AUDIO SYSTEM SET-UP Match the numbers below to the diagram for speaker placement and refer to the table for the different surround sound requirements. These speakers are connected to the Rear Speaker 8 Ohm output on the TV. (Click to see Audio System Set-Up) * See page 10 for location of Surround Switch. THE REMOTE CONTROL (CLU-415UI) In addition to controlling all the functions on your HITACHI Projection TV, the new remote is designed to operate different types of VCR's and different types of CATV (Cable TV) converters with one touch. To operate your TV, point the remote at the remote sensor of the TV, and press the TV button on the remote. To operate your VCR, point the remote at the remote sensor of the VCR, and press the VCR button. To operate your Cable Box, point the remote at the remote sensor of the Cable Box, and press the THE REMOTE CONTROL (CLU-415UI) CABLE button on the remote. Click to see the Remote - 16 - Q These buttons allow the remote to control your TV, VCR, or Cable Box depending of which mode is chosen, as explained above. R TV/VCR BUTTON When the remote is in the TV or VCR mode, this is the TV/VCR button. When the remote is in the CABLE mode, this is the A/B button. S PRECODED VCR BUTTONS These buttons always transmit the chosen precoded VCR codes. T RESET BUTTON Press RESET to return video and audio to factory settings. U, V LIGHT BUTTON V When you are in a darkroom, press this button on the side of the remote to light up the buttons shown in . The light will stay on for about 8 seconds if the light button is not pressed again. Click to see Remote Q POWER button Press this button to turn the TV set on or off. If MESSAGE-1 or MESSAGE-2 is set, it will be displayed when the TV is first turned on. (See page 32. ) R RECALL button When you want to check the channel being received, or if it has a stereo (ST) or second audio program (SAP), press the RECALL button. You can also check the time, and if the ON TIME or OFF TIME has been set. (See page 31. ) pic You can also use the RECALL button to quickly clear many of the other on-screen displays. THE REMOTE CONTROL (CLU-415UI) - 17 - S MENU, ENTER, CURSOR buttons All the on-screen display features can be set or adjusted by using these buttons. The "CURSOR" buttons will highlight functions or adjust different features. The "ENTER" button will set features to your preference. T CHANNEL SELECTOR buttons "CHANNEL SELECTOR" buttons are used to set the time, for channel memory, etc. [. . . ] This Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage or power surges. IF YOUR SET SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1) Push the power switch (ON/OFF switch) once. 2) If there is still no power, wait 30 seconds and push the power switch again. This protective technology should provide for years of lasting entertainment from your Projection Television. [. . . ]