User manual HITACHI 43FWX20B

[. . . ] PROJECTION COLOR TV 57UWX20B 51UWX20B 43FWX20B 57GWX20B 51GWX20B OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-17 THE REMOTE CONTROL 18-31 Video Audio Ch. Manager Locks Setup Move SEL ON-SCREEN DISPLAY 32-56 Sel USEFUL INFORMATION INDEX 57-62 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. [. . . ] Press and release the cable/satellite (CBL/SAT) button to switch to cable/satellite pre-coded mode. Hold down the CBL/SAT button on the remote and enter the two digit preset code that matches your cable/satellite box as shown on page 31. The remote will turn off your cable/satellite box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable/satellite box. The remote will now control your cable/satellite box. POWER TV CBL/SAT DVD/VCR 5. 6. NOTES: 1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box code has not been precoded into the remote. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures, please consult your cable/satellite box operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. PIP VIDEO SWAP PIP MODE PIP CH FREEZE MENU SELECT 3. MUTE EXIT LAST CH VOL CH CABLE (CBL/SAT) button This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode. PRECODED CABLE/SATELLITE BOX buttons These buttons transmit the chosen precoded cable/satellite codes. EXCLUSIVE TV buttons These buttons are for operating the TV. 1 4 7 ANT 2 5 8 0 VID3 3 6 9 INFO VID1 VID2 VID4 REC VID5 ASPECT VIRTUAL HD CLU-4321UG MY CABLE/SATELLITE BOX CODE IS: NOTE: Refer to instruction manual of the Cable/Satellite Box for operation of the buttons exclusively for the Cable/Satellite Box. 29 USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. You must first program the remote to match the remote system of your DVD player. Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 31. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code. The remote will now control your DVD player. 5. 6. POWER NOTES: 1. If your DVD player cannot be operated after performing the above procedures, your DVD player's code has not been precoded into the remote. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. TV CBL/SAT DVD/VCR PIP VIDEO SWAP PIP MODE PIP CH FREEZE MENU SELECT MUTE EXIT LAST CH VOL CH DVD/VCR Button This button allows the remote to control your DVD player by setting it to DVD mode. PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. [. . . ] Do not use an old battery with a new battery. Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp, resulting in a distorted picture. 57 Reception Problems · IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. · GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. [. . . ]