User manual HITACHI 42V525

[. . . ] LCD REAR PROJECTION TELEVISION Operating Guide for 42V525 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-33 ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 33. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code. You will need to set the display type of your DVD player to 16:9 widescreen. 5. 6. If your DVD player cannot be operated after performing the above procedures, your DVD player's code has not been precoded into the remote. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. DVD button This button allows the remote to control your DVD player by setting it to DVD mode. PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. MY DVD PLAYER CODE IS: NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player. 31 USING YOUR REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. You must first program the remote to match the remote system of your VCR (refer to page 33 for pre-codes). Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 33. The remote will turn off your VCR when the correct two digit preset code is entered. The remote will now control your VCR. 5. 6. THE REMOTE CONTROL NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR's code has not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. Press the Record button twice to record. VCR button This button allows the remote to control your VCR player by setting it to VCR mode. PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. MY VCR CODE IS: NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 32 VCR, CABLE, SATELLITE, AND DVD REMOTE VCR BRAND. [. . . ] One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. · RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. NOTE: The TV set can generate sound distortion in external devices such as a radio. [. . . ]