User manual HITACHI 42PD8700U

[. . . ] Instructions for use GB 42PD8700U Contents Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 9 Inserting Batteries In The Remote Control Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Operating The TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 TV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Common Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Obtain the Conditional Access Module (CAM) and the Viewing card by subscribing to a pay channel company, then insert those to the Television using the following procedure. Insert the CAM, then Viewing Card to the slot that is located in the terminal cover at the left-hand side of the TV (from front view). · The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. Analogue TV Menu System Your TV has been designed with a menu system to provide easy manipulation of a multifunction system. Press / button to select a menu title and then / button to select a menu item and / or "OK" button to enter the menu item. button to return to the previous Picture menu By pressing / button, select the first icon. Picture menu appears on the screen. PICTURE Mode Contrast Brightness Sharpness Colour Colour Temp Noise Reduction Film Mode 3D Comb Reset PAL 50Hz Cinema 62 24 10 32 Warm Medium Off Off - 18 - Mode / button, select Mode. By pressing Press / button to choose one of these options: Natural, Dynamic and Cinema. Hue This item is displayed in picture menu when the TV receives an NTSC signal. Press / button to choose one of these options: Cool, Normal and Warm. Noise Reduction This item is used to reduce the image noise and improve the picture quality at weak signals. Press / button to set Noise reduction level to Off, Low, Medium or High. Film Mode Films are recorded at a different number of frames per second to normal television programmes. Turn this feature on when you are watching films to see the fast motion scenes clearly. 3D Comb 3D Comb is used to improve colour transitions and colour quality of pictures. By pressing Press / or "OK" button to reset the picture modes to factory default settings. Sound menu By pressing / button, select the second icon. Sound menu appears on the screen. SOUND Volume Equalizer Balance Headphone Sound Mode AVL Effect Dynamic Bass 3DS Subwoofer 10 0 Stereo On Off Off On Off - 19 - Volume / By pressing Press button to Press button to Volume level can and 63. Press / or "OK" button to enter equalizer menu. SOUND Equalizer Sound Mode 120Hz 500Hz 1. 5kHz 5kHz 10kHz User 0 0 0 0 0 button, select Volume. be adjusted between 0 SOUND Headphone Volume Sound Mode Balance 10 Stereo 0 volume / button, select Volume. / / button, select Sound button to change sound In equalizer menu the sound mode can be changed to User, Pop, Rock, Jazz, Flat and Classic by pressing / button. Select the desired frequency by / button and increase or decrease the frequency gain by pressing / button. button, select Heador "OK" button to enter button to return to the previous Sound mode is used to identify sound mode of the headphone and can be set to mono, stereo, dual a or dual b according to the transmission. You can select Mono, Stereo, Dual A or Dual B mode, only if the selected channel supports that mode. [. . . ] Please note that evidence of the date of purchase will be required before any service under this guarantee is carried out. THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS. IN ALL CASES OF DIFFICULTY PLEASE CONSULT YOUR HITACHI DEALER QUICK GUIDE GB 42PD8700 U IMPORTANT - If placing TV into cabinet or alcove, ensure there is at least a 100mm (10cm) gap to the sides, rear and top of the TV. Please read the main Users Guide for more safety information before installation. insert the batteries into your handset either connect the aerial straight to your TV. . . Rear view Aerial (RF) Lead wall socket Scart 1 Scart 2 Aerial (RF) Socket . . . or connect the aerial through a VCR. . . PLASMA TV Scart 3 Aerial (RF) Socket Scart 1 Scart 2 (RF) connector lead VCR to TV wall socket Optional Scart Lead Aerial (RF) Socket VCR TV to VCR ANT. IN Aerial (RF) Lead AV-1 AV-2 VCR · It is recommended that a scart lead should be fitted between your TV and VCR to enhance your picture and sound quality. Scart leads are essential if you have a stereo TV and VCR and wish to obtain stereo sound from your equipment. These leads can be purchased from your Hitachi dealer or any good High Street electrical retailer. . . . or through a satellite decoder. . . PLASMA TV GB Aerial RF Lead from Satellite to TV · Scart Lead to EXT-1 on TV. TV ANT. IN VCR RF Lead to Aerial Satellite LNB lead . . . or through a VCR and satellite decoder. PLASMA TV RF Lead from VCR to TV · Scart Lead to AV-1 on TV. RF Lead from Satellite to VCR Aerial TV ANT. IN VCR RF Lead to Aerial Satellite LNB lead ANT. IN AV-1 AV-2 VCR connect the TV plug to the mains socket GB European plug UK plug Power Cord Power on/off Input button Plug the mains lead into the TV. . . insert plug. . . . . . and switch on insert plug. . . switch your TV on by pressing the On/Off button Front View NB: When the set is first switched on, the set will be in standby and the indicator on the front of the set will illuminate red. [. . . ]