User manual HITACHI 42PD7A10
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HITACHI 42PD7A10. We hope that this HITACHI 42PD7A10 user guide will be useful to you.
You may also download the following manuals related to this product:
HITACHI 42PD7A10 (1160 ko)
HITACHI 42PD7A10 (1195 ko)
HITACHI 42PD7A10 (1171 ko)
HITACHI 42PD7A10 (1184 ko)
HITACHI 42PD7A10 (1191 ko)
HITACHI 42PD7A10 (1471 ko)
HITACHI 42PD7A10 (1155 ko)
HITACHI 42PD7A10 (1116 ko)
HITACHI 42PD7A10 (1167 ko)
HITACHI 42PD7A10 (1110 ko)
Manual abstract: user guide HITACHI 42PD7A10
Detailed instructions for use are in the User's Guide.
[. . . ] Model PW2 42PD7A10 42PD7200 42PD7A10A 42PD7200A
Important
Please read this User's Manual thoroughly, especially the Safety Instructions on Page 4 to 7. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to yourself. Should you encounter any difficulty in the set-up or operation of your monitor, firstly refer to the Troubleshooting guide at the rear of this manual. In the unlikely event of a problem occurring with your plasma monitor, switch off at the mains sockets, pull out the plugs, and contact your dealer immediately.
FEATURES
Large-screen, high-definition plasma display panel
The 42-inch colour plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, creates a high-definition, large-screen (aspect ratio : 16:9) and low-profile flat display. [. . . ] Adjust for preferred angle.
Opposite directions are displayed on the screen whilst the monitor is swivelled. Swivelling angle of the monitor is available within 30 degrees from the front face.
ATTENTION
· Do not push the panel manually whilst using the swivel function. · Do not put hands or faces close to the monitor whilst operating the swivel function. · Do not put any object, like a vase, near the monitor in swiveling area. It would cause a breakage of the object and /or a failure of the stand. · Place the monitor on the stable location, or the swivel function would not operate correctly. · In the case of using the monitor wall mounted, be sure to detach the connecting cable between the monitor and the stand.
Caution when connecting the monitor with the stand
· When detaching the stand from the monitor, make sure to detach the connector cable from the stand connection terminal on the rear of the monitor.
Pinch right and left locks of the connector and pull out downward.
· When attaching the stand to the monitor once again, insert the connector cable into the stand connection terminal on the rear of the monitor.
· Make sure that the direction of the connector for stand connecting cable is correct.
25
OPERATING INSTRUCTIONS (continued) Input Signal Screen Display
RECALL button
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control.
· The display will go out in approximately 6 seconds.
TV
1 ABCDE
TV position Name Sound mode
Off-timer On-timer
OFF
-- -- Min. -- -- : -- --
BG
VIDEO
AV1 Composite
Input mode Signal mode
Off-timer On-timer
OFF
-- -- Min. -- -- : -- --
RGB
RGB2 RGB H : 48. 4kHz V : 60. 1 Hz
Off-timer On-timer
OFF
-- -- Min. -- -- : -- --
Input mode Signal mode Input horizontal frequency Input vertical frequency
26
OPERATING INSTRUCTIONS (continued)
RECALL button
INPUT SELECT buttons SELECT/ADJUST button (, , , ) CHANNEL UP/DOWN button
Displaying MULTI PICTURE
If the MULTI PICTURE button on the remote control is pressed, multi pictures will display. And then three types of the screen can be selected by pressing the MULTI MODE button on the remote control. The multi picture mode will change in the following sequence each time the MULTI MODE button is pressed. 2 pictures (Split) 4 pictures 12 pictures
MULTI MODE button MULTI PICTURE button
Activating the Split mode from the TV screen Pressing the MULTI PICTURE button one time will display 2 pictures.
· The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio will be output from the side on which the speaker icon is located. · The same signal input cannot be selected for both screens at the same time. · The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control. · The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected by pressing INPUT SELECT buttons on the remote control. · Pressing the MULTI PICTURE button once again will cancel the multi picture mode. 28
5 AV1
A
B
Activating the 4 pictures mode from the TV screen Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
· Press and SELECT buttons to select picture A or picture B indicated by a red triangle. · The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control. · The audio can only be output from picture A in 4 pictures mode. · The component signal input mode cannot be selected in pictures B. 28 · Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. [. . . ] In this case, use H/V separate sync, H/V composite sync.
(
) : With component input
S-input connector pin specifications
Pin 1 2 3 4 Frame Input signal Y Y-GND C C-GND GND
HDMI connector pin specifications
Pin 1 2 3 4 5 6 7 8 9 10 Input signal TMDS Data2+ TMDS Data2 Shield TMDS Data2TMDS Data 1+ TMDS Data1 Shield TMDS Data1TMDS Data0+ TMDS Data0 Shield TMDS Data0TMDS Clock+ Pin 11 12 13 14 15 16 17 18 19 Input signal TMDS Clock Shield TMDS ClockCEC Reserved(N. C. on device) SCL SDA DDC/CED Ground +5V Power Hot Plug Detect
DVI terminal (DVI-D)
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Input signal T. M. D. S. Data3+ Pin 14 15 16 17 18 19 20 21 22 23 24 Frame Input signal +5V Power Ground (for+5V) Hot Plug Detect T. M. D. S. ClockGND
12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
51
PRODUCT SPECIFICATIONS (continued) Signal Input (continued)
Scart connector pin specifications
Pin 1 2 3 4 5 6 7 8 9 10 11 Signal AUDIO OUT (RIGHT) AUDIO IN (RIGHT) AUDIO OUT (LEFT/MONO) AUDIO GND RGB-B GND AUDIO IN (LEFT/MONO) RGB-B IN AUDIO/RGB SWITCH / 16:9 RGB-G GND Not Used RGB-G IN Pin 12 13 14 15 16 17 18 19 20 21 Signal Not Used RGB-R GND GND RGB-R / S. VHS CHROMINANCE IN BLANKING SIGNAL COMPOSITE VIDEO GND BLANKING SIGNAL GND COMPOSITE VIDEO OUT COMPOSITE VIDEO / S. VHS LUMINANCE IN GND / SHIELD (CHASSIS)
20
18
16
14
12
10
8
6
4
2
21 19
17
15
13
11
9
7
5
3
1
Recommended Signal List
Applicable video signals for input terminal
Terminal
Signal AV1 AV2 AV3 AV4 AV5 AV6 RGB1 RGB2 Refer to Setup Menu Refer to Setup Menu ( 33 33 CVBS
RCA/S-video/SCART
S-video Component SCART (RGB)
HDMI
PC
DVI
STB RGB
D-sub
Component
Remarks
Refer to Setup Menu Refer to Setup Menu Refer to Setup Menu Refer to Setup Menu Refer to Setup Menu
33 33 33 33 33
: Available)
With composite input(AV1~AV5 input) and S-video input (AV1, AV5 input)
Signal mode No.
1 2
Signal Name
NTSC4. 43 NTSC3. 58 PAL SECAM
Resolution
525 625
Vertical frequency (Hz)
59. 94 50. 00
Horizontal frequency (kHz)
15. 73 15. 63
Dot clock frequency (MHz)
-- --
Remarks
With component input (AV4 and RGB2-component input)
Signal mode No.
1 2 3 4 5 6 7 8
*1 720p/50 is supported AV4 only.
Signal Name
576i 480i 576p 480p 1080i/50 1080i/60 720p/50*1 720p/60
Resolution
576 480 576 480 1080 1080 720 720
Vertical frequency (Hz)
50. 00 59. 94 50. 00 59. 94 50. 00 60. 00 50. 00 60. 00
Horizontal frequency (kHz)
15. 63 15. 73 31. 26 31. 47 28. 13 33. 75 37. 50 45. 00
Dot clock frequency (MHz)
-- -- -- -- -- -- -- --
Remarks
52
PRODUCT SPECIFICATIONS (continued)
ENGLISH
53
Recommended Signal List (continued)
With HDMI input (AV6 input)
Signal mode No.
1 2 3 4 5 6 7 8 9
Signal Name
VGA 576i 480i 576p 480p 1080i/50 1080i/60 720p/50 720p/60
Resolution
640 x 480 720(1440) x 576 720(1440) x 480 720 x 576 720 x 480 1920 x 1080 1920 x 1080 1280 x 720 1280 x 720
Vertical frequency (Hz)
59. 94 50. 00 59. 94 50. 00 59. 94 50. 00 60. 00 50. 00 60. 00
Horizontal frequency (kHz)
31. 47 15. 63 15. 73 31. 25 31. 47 28. 13 33. 75 37. 50 45. 00
Dot clock frequency (MHz)
25. 18 27. 00 27. 00 27. 00 27. 00 74. 25 74. 25 74. 25 74. 25
Remarks
EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B
With Digital signal input
Signal mode No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Signal Name
VGA W-VGA
Resolution
640 X 400 640 X 480 864 X 480 640 X 480 640 X 480 640 X 480 800 X 600 800 X 600 800 X 600 800 X 600 800 X 600 1024 X 768 1024 X 768 1024 X 768 720 X 480 720 X 576 1280 X 720 1280 X 720 1920 X 1080 1920 X 1080
Horizontal Dot clock Setup Menu Condition Vertical frequency frequency frequency DVI-PC DVI-STB (kHz) (MHz) (Hz)
70. 08 59. 94 59. 94 72. 81 75. 00 85. 01 56. 25 60. 32 72. 19 75. 00 85. 06 60. 00 70. 07 75. 03 59. 94 50. 00 50. 00 60. 00 60. 00 50. 00 31. 47 31. 47 31. 47 37. 86 37. 50 43. 27 35. 16 37. 88 48. 08 46. 88 53. 67 48. 36 56. 48 60. 02 31. 47 31. 25 37. 50 45. 00 33. 75 28. 13 25. 18 25. 18 34. 24 31. 50 31. 50 36. 00 36. 00 40. 00 50. 00 49. 50 56. 25 65. 00 75. 00 78. 75 27. 00 27. 00 74. 25 74. 25 74. 25 74. 25
Remarks
WVGA type : On
VESA
480p 576p 720p/50 720p/60 1080i/60 1080i/50
EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B ( : acceptable)
PRODUCT SPECIFICATIONS (continued) Recommended Signal List (continued)
With Analog signal input (RGB2 input)
Signal mode No. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HITACHI 42PD7A10
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HITACHI 42PD7A10 will begin.