User manual HITACHI 42PD7200

[. . . ] Model PW2 42PD7A10 42PD7200 42PD7A10A 42PD7200A Important Please read this User's Manual thoroughly, especially the Safety Instructions on Page 4 to 7. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to yourself. Should you encounter any difficulty in the set-up or operation of your monitor, firstly refer to the Troubleshooting guide at the rear of this manual. In the unlikely event of a problem occurring with your plasma monitor, switch off at the mains sockets, pull out the plugs, and contact your dealer immediately. FEATURES Large-screen, high-definition plasma display panel The 42-inch colour plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, creates a high-definition, large-screen (aspect ratio : 16:9) and low-profile flat display. [. . . ] Adjust for preferred angle. Opposite directions are displayed on the screen whilst the monitor is swivelled. Swivelling angle of the monitor is available within 30 degrees from the front face. ATTENTION · Do not push the panel manually whilst using the swivel function. · Do not put hands or faces close to the monitor whilst operating the swivel function. · Do not put any object, like a vase, near the monitor in swiveling area. It would cause a breakage of the object and /or a failure of the stand. · Place the monitor on the stable location, or the swivel function would not operate correctly. · In the case of using the monitor wall mounted, be sure to detach the connecting cable between the monitor and the stand. Caution when connecting the monitor with the stand · When detaching the stand from the monitor, make sure to detach the connector cable from the stand connection terminal on the rear of the monitor. Pinch right and left locks of the connector and pull out downward. · When attaching the stand to the monitor once again, insert the connector cable into the stand connection terminal on the rear of the monitor. · Make sure that the direction of the connector for stand connecting cable is correct. 25 OPERATING INSTRUCTIONS (continued) Input Signal Screen Display RECALL button The input signal status can be displayed on the screen by pressing the RECALL button of the remote control. · The display will go out in approximately 6 seconds. TV 1 ABCDE TV position Name Sound mode Off-timer On-timer OFF -- -- Min. -- -- : -- -- BG VIDEO AV1 Composite Input mode Signal mode Off-timer On-timer OFF -- -- Min. -- -- : -- -- RGB RGB2 RGB H : 48. 4kHz V : 60. 1 Hz Off-timer On-timer OFF -- -- Min. -- -- : -- -- Input mode Signal mode Input horizontal frequency Input vertical frequency 26 OPERATING INSTRUCTIONS (continued) RECALL button INPUT SELECT buttons SELECT/ADJUST button (, , , ) CHANNEL UP/DOWN button Displaying MULTI PICTURE If the MULTI PICTURE button on the remote control is pressed, multi pictures will display. And then three types of the screen can be selected by pressing the MULTI MODE button on the remote control. The multi picture mode will change in the following sequence each time the MULTI MODE button is pressed. 2 pictures (Split) 4 pictures 12 pictures MULTI MODE button MULTI PICTURE button Activating the Split mode from the TV screen Pressing the MULTI PICTURE button one time will display 2 pictures. · The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio will be output from the side on which the speaker icon is located. · The same signal input cannot be selected for both screens at the same time. · The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control. · The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected by pressing INPUT SELECT buttons on the remote control. · Pressing the MULTI PICTURE button once again will cancel the multi picture mode. 28 5 AV1 A B Activating the 4 pictures mode from the TV screen Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures. · Press and SELECT buttons to select picture A or picture B indicated by a red triangle. · The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control. · The audio can only be output from picture A in 4 pictures mode. · The component signal input mode cannot be selected in pictures B. 28 · Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. [. . . ] In this case, use H/V separate sync, H/V composite sync. ( ) : With component input S-input connector pin specifications Pin 1 2 3 4 Frame Input signal Y Y-GND C C-GND GND HDMI connector pin specifications Pin 1 2 3 4 5 6 7 8 9 10 Input signal TMDS Data2+ TMDS Data2 Shield TMDS Data2TMDS Data 1+ TMDS Data1 Shield TMDS Data1TMDS Data0+ TMDS Data0 Shield TMDS Data0TMDS Clock+ Pin 11 12 13 14 15 16 17 18 19 Input signal TMDS Clock Shield TMDS ClockCEC Reserved(N. C. on device) SCL SDA DDC/CED Ground +5V Power Hot Plug Detect DVI terminal (DVI-D) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Input signal T. M. D. S. Data3+ Pin 14 15 16 17 18 19 20 21 22 23 24 Frame Input signal +5V Power Ground (for+5V) Hot Plug Detect T. M. D. S. ClockGND 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 51 PRODUCT SPECIFICATIONS (continued) Signal Input (continued) Scart connector pin specifications Pin 1 2 3 4 5 6 7 8 9 10 11 Signal AUDIO OUT (RIGHT) AUDIO IN (RIGHT) AUDIO OUT (LEFT/MONO) AUDIO GND RGB-B GND AUDIO IN (LEFT/MONO) RGB-B IN AUDIO/RGB SWITCH / 16:9 RGB-G GND Not Used RGB-G IN Pin 12 13 14 15 16 17 18 19 20 21 Signal Not Used RGB-R GND GND RGB-R / S. VHS CHROMINANCE IN BLANKING SIGNAL COMPOSITE VIDEO GND BLANKING SIGNAL GND COMPOSITE VIDEO OUT COMPOSITE VIDEO / S. VHS LUMINANCE IN GND / SHIELD (CHASSIS) 20 18 16 14 12 10 8 6 4 2 21 19 17 15 13 11 9 7 5 3 1 Recommended Signal List Applicable video signals for input terminal Terminal Signal AV1 AV2 AV3 AV4 AV5 AV6 RGB1 RGB2 Refer to Setup Menu Refer to Setup Menu ( 33 33 CVBS RCA/S-video/SCART S-video Component SCART (RGB) HDMI PC DVI STB RGB D-sub Component Remarks Refer to Setup Menu Refer to Setup Menu Refer to Setup Menu Refer to Setup Menu Refer to Setup Menu 33 33 33 33 33 : Available) With composite input(AV1~AV5 input) and S-video input (AV1, AV5 input) Signal mode No. 1 2 Signal Name NTSC4. 43 NTSC3. 58 PAL SECAM Resolution 525 625 Vertical frequency (Hz) 59. 94 50. 00 Horizontal frequency (kHz) 15. 73 15. 63 Dot clock frequency (MHz) -- -- Remarks With component input (AV4 and RGB2-component input) Signal mode No. 1 2 3 4 5 6 7 8 *1 720p/50 is supported AV4 only. Signal Name 576i 480i 576p 480p 1080i/50 1080i/60 720p/50*1 720p/60 Resolution 576 480 576 480 1080 1080 720 720 Vertical frequency (Hz) 50. 00 59. 94 50. 00 59. 94 50. 00 60. 00 50. 00 60. 00 Horizontal frequency (kHz) 15. 63 15. 73 31. 26 31. 47 28. 13 33. 75 37. 50 45. 00 Dot clock frequency (MHz) -- -- -- -- -- -- -- -- Remarks 52 PRODUCT SPECIFICATIONS (continued) ENGLISH 53 Recommended Signal List (continued) With HDMI input (AV6 input) Signal mode No. 1 2 3 4 5 6 7 8 9 Signal Name VGA 576i 480i 576p 480p 1080i/50 1080i/60 720p/50 720p/60 Resolution 640 x 480 720(1440) x 576 720(1440) x 480 720 x 576 720 x 480 1920 x 1080 1920 x 1080 1280 x 720 1280 x 720 Vertical frequency (Hz) 59. 94 50. 00 59. 94 50. 00 59. 94 50. 00 60. 00 50. 00 60. 00 Horizontal frequency (kHz) 31. 47 15. 63 15. 73 31. 25 31. 47 28. 13 33. 75 37. 50 45. 00 Dot clock frequency (MHz) 25. 18 27. 00 27. 00 27. 00 27. 00 74. 25 74. 25 74. 25 74. 25 Remarks EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B With Digital signal input Signal mode No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Signal Name VGA W-VGA Resolution 640 X 400 640 X 480 864 X 480 640 X 480 640 X 480 640 X 480 800 X 600 800 X 600 800 X 600 800 X 600 800 X 600 1024 X 768 1024 X 768 1024 X 768 720 X 480 720 X 576 1280 X 720 1280 X 720 1920 X 1080 1920 X 1080 Horizontal Dot clock Setup Menu Condition Vertical frequency frequency frequency DVI-PC DVI-STB (kHz) (MHz) (Hz) 70. 08 59. 94 59. 94 72. 81 75. 00 85. 01 56. 25 60. 32 72. 19 75. 00 85. 06 60. 00 70. 07 75. 03 59. 94 50. 00 50. 00 60. 00 60. 00 50. 00 31. 47 31. 47 31. 47 37. 86 37. 50 43. 27 35. 16 37. 88 48. 08 46. 88 53. 67 48. 36 56. 48 60. 02 31. 47 31. 25 37. 50 45. 00 33. 75 28. 13 25. 18 25. 18 34. 24 31. 50 31. 50 36. 00 36. 00 40. 00 50. 00 49. 50 56. 25 65. 00 75. 00 78. 75 27. 00 27. 00 74. 25 74. 25 74. 25 74. 25 Remarks WVGA type : On VESA 480p 576p 720p/50 720p/60 1080i/60 1080i/50 EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B EIA-861B ( : acceptable) PRODUCT SPECIFICATIONS (continued) Recommended Signal List (continued) With Analog signal input (RGB2 input) Signal mode No. [. . . ]