User manual HITACHI 42HDW10

[. . . ] Color Plasma Display Monitor Model PD1 42HDW10 USER'S MANUAL MANUEL UTILISATEUR Hitachi America, Ltd. Home Electronics Division 1855 Dornoch Court San Diego, CA 92154 Tel : 1-800-HITACHI (1-800-448-2244) The stand is an option. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS. [. . . ] RGB1 (D-sub input) · When the same signal is input to RGB1 and RGB2, the phase may in some cases shift slightly but this is not a malfunction. In such case, readjust the PHASE of the one being used. Main unit RGB2 (BNC input) VIDEO1 (composite or S input) INPUT SELECT VIDEO2 (COMPONENT input) Volume Adjustment I While the on-screen display system, ( 12 ) is not on display, press the remote controller VOLUME button VOLUME+ or VOLUME- (or the main unit VOLUME button L or M to adjust the sound volume. controller · The adjustment status will be displayed as VOLUME+ Sound volume setting guidance while you press these buttons. · While the guidance is on display, press VOLUME+ VOLUMEor L to turn up the volume. VOLUME : 30 · While the guidance is on display, press VOLUME- Main unit or M to turn down the volume. Adjustment status guidance · You can also adjust the sound volume setting VOLUME via the on-screen display system 14 . · The sound volume adjustment mode will exit when no keys are entered for 5 seconds. (The adjustment status guidance will disappear automatically. ) Remote Sound Mute I Press the remote controller MUTE button to mute the sound temporarily. · When you press the button, [MUTE] (pink) and the status of volume setting will be displayed in a guidance image. · While the sound is muted, press the VOLUME- button to turn down the volume. · While the sound is muted, press the VOLUME+ button to cancel the mute. · You can also adjust the sound volume setting of the mute via the on-screen display system 14 . Sound volume setting Remote controller MUTE MUTE : 30 (The display will turn to pink. ) I Press the remote controller MUTE button once again and the mute will be canceled and the guidance will change to VOLUME (blue), enabling the volume to be heard. · When MUTE is used, the guide display will continue for 5 sec. and then turn off. 10 Contrast Adjustment I While the on-screen display system 12 , is not on display, press the remote controller SELECT button or to adjust the contrast. · When you press these buttons, the status of contrast adjustment and the input horizontal (H) and vertical (V) frequencies of the input signal will be displayed in a guidance image. (For RGB input only) · While the guidance is on display, press the key to narrow the difference between darkness and brightness. · While the guidance is on display, press the key to widen the difference between darkness and brightness. · You can also adjust the contrast setting via the on-screen display system 13 . · The contrast adjustment mode will exit when no keys are entered for 5 seconds. (The adjustment status guidance will disappear automatically. ) VIDEO Remote controller CONTRAST : 100 Contrast setting RGB CONTRAST : 100 H: **. *Hz Input vertical frequency Input horizontal frequency Adjustment status guidance Size Selection I Each press on the SIZE button on the remote control switches the display size of the screen (or the display area) in the following order. The selected mode is displayed in the lower part of the screen. ·RGB signal input NORMAL FULL ZOOM Remote controller SIZE FULL ·VIDEO signal input 4:3 PANORAM. FULL MOVIE1 MOVIE2 · Depending on the signal type, sometimes it may not be possible to change screen size. 15 16 Input Signal Status Display I Press the remote controller RECALL button to display the status of input signals on the screen. Remote I Press the remote controller RECALL button controller RECALL once again to exit the screen display. · The Menu will clear 5 seconds later. VIDEO VIDEO2 [COMPONENT] Input terminal name RGB RGB1 [D-SUB] H : 46. 5kHz, V : 60. 0Hz Input horizontal frequency Input vertical frequency 11 ENGLISH OPERATING INSTRUCTIONS (continued) On-Screen Display System ENGLISH I Press the MENU button to open an MAIN MENU allowing you to complete various adjustments and settings using the SELECT buttons (The , , , and keys of the remote controller or the SELECT or VOLUME button of the main unit. ). Pink · Press the SELECT button of the main unit ( or key of the remote controller) to select an item by moving the pink text. [. . . ] (AJUSTMENT OK) (Ajustez en affichant un motif fin, tel qu'une suite de caractères ou une traînée verticale sur l'écran. ) Si AUTO ADJUST ne fonctionne pas de façon satisfaisante. 7) Appuyez plusieurs fois sur la touche SELECT pour choisir AFFICHAGE. (Ajustez l'horloge en affichant un motif fin, tel qu'une suite de caractères ou une traînée verticale sur l'écran. ) 12) Appuyez sur la touche ou pour que le texte apparaisse uniforme sur tout l'écran. 13) Si le texte apparaît flou sur tout l'écran, procédez au réglage décrit dans Symptôme 2. · L'image affichée peut être momentanément perturbée pendant le réglage de l'horloge mais cela ne traduit pas une panne. 25 FRANÇAIS Image 1 Vertical streaks Before adjustment Some characters are blurred. GUIDE DE DÈPANNAGE (suite) Symptôme 2 Le texte affiché sur l'ensemble de l'écran apparaît flou dans sa totalité (image 2). [. . . ]