User manual HITACHI 37LD8600

[. . . ] Instructions for use Bedienungsanleitung GB D F I 37LD8600 Notice d'utilisation Istruzioni per l'uso Contents Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connections To The Aerial Input Socket8 How To Connect Other Devices . . . . . . . . . . . 8 Inserting Batteries In The Remote Control Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Initial APS (Automatic Programming System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press _ / ` button to change the colour system to PAL, PAL60, SECAM or AUTO. Press _ / ` button to adjust the tuning. - 13 - Search By pressing a / b button, select Search. You can also enter a frequency value directly by pressing the digit buttons. VCR (Video Cassette Recorder) This item can be seen in all modes except EXT-3, EXT-5 and PC. If you want to watch a VCR source from one of these modes, then it will be better to set VCR mode on. For this, while the cursor is on this item press the _ / ` buttons to set it On. Program Stored will be displayed on the screen. Name: To change the name of a decided programme, select the programme and press the RED button. Press a / b button to change that letter and _ / ` button to select the other letters. Insert: Select the programme which you want to insert by navigation buttons. By navigation buttons move the selected programme to the decided programme space and press the GREEN button again. Pressing the YELLOW button again erases the selected programme from the programme list, and the programmes below shift one up. APS (Automatic Programming System) When you press the BLUE button for APS, the following warning screen will be displayed. Program menu By pressing _ / ` button, select the fifth icon. Program menu appears on the screen. By moving the cursor in four directions you can reach 20 programmes in the same page. You can scroll the pages up or down by pressing the navigation buttons to see all the programmes in TV mode (except the AV mode). By cursor action, programme selection is done automatically. Press the BLUE button to cancel APS if you do not want to delete your existing programme list. To continue APS, first select the country by pressing _ / ` button and then press the RED or OK button. - 14 - Menu System in PC mode After APS is finalized, the programme table will appear on the screen. The menu will be displayed in the middle of the screen. PC Picture Position Menu By pressing _ / ` button, select the first icon. PC Picture Position menu appears on the screen. Source menu By pressing _ / ` button, select the sixth icon. Source menu appears on the screen. In source menu, highlight a source by pressing a / b button and switch to that mode by pressing _ / ` or OKbutton. Autoposition If you shift the picture horizontally or vertically to an unwanted position, use this item to put the picture into correct place automatically. Warning: Auto position adjustment recommended to be done with the full screen image for the proper adjustment. H (Horizontal) Position This item shifts the image horizontally to right hand side or left hand side of the screen. V (Vertical) Position This item shifts the image vertically towards the top or bottom of the screen. [. . . ] Please read the main Users Guide for more safety information before installation. insert the batteries into your handset Rear view either connect the aerial straight to your TV. . . Scart 1 Scart 2 Aerial (RF) Lead wall socket Aerial (RF) Socket . . . or connect the aerial through a VCR. . . TFT-LCD TV Aerial (RF) Socket Scart 2 Scart 1 (RF) connector lead VCR to TV wall socket Optional Scart Lead Aerial (RF) Socket VCR TV to VCR ANT. IN Aerial (RF) Lead AV-1 AV-2 VCR · It is recommended that a scart lead should be fitted between your TV and VCR to enhance your picture and sound quality. Scart leads are essential if you have a stereo TV and VCR and wish to obtain stereo sound from your equipment. These leads can be purchased from your Hitachi dealer or any good High Street electrical retailer. . . . or through a satellite decoder. . . TFT-LCD TV GB Aerial RF Lead from Satellite to TV · Scart Lead to EXT-1 on TV. TV ANT. IN VCR RF Lead to Aerial Satellite LNB lead . . . or through a VCR and satellite decoder. TFT-LCD TV RF Lead from VCR to TV · Scart Lead to EXT-1 on TV. RF Lead from VCR to Satellite Aerial ANT. IN TV VCR RF Lead to Aerial Satellite LNB lead ANT. IN AV-1 AV-2 VCR connect the TV plug to the mains socket UK plug Power Cord Power on/off Input button GB European plug Plug the mains lead into the TV. . . insert plug. . . . . . and switch on insert plug. . . switch your TV on by pressing the On/Off button TV/AV MENU P/CH Front View NB: When the set is first switched on, the set will be in standby and the indicator on the front of the set will illuminate red . Press the channel up down (P- , P+) or numeric buttons (1, 2, 3, . . . ) to operate. basic functions of remote control To enter the main menu Volume Down* To return to previous menu Programme Up* Volume Up* Programme Down* To select a programme number. *Also used for navigation in menus important note before starting Auto Setup If you have a Video Cassette Recorder or a Satellite receiver connected to your TV please ensure that they are switched on before automatic tuning begins. [. . . ]