User manual HITACHI 32PD5000

[. . . ] Colour Plasma Display Monitor Model PW1 32PD5000 42PD5000 42PMA500 CMP4214E USER'S MANUAL MANUEL UTILISATEUR BEDIENUNGSANLEITUNG Th is It mo ca d n el ho is w no ev t er cla ac ss ce ed pt a 10 s H 80 D i 5 Re 0 ad si y gn b al ec s au an s d ei di t c sp a la nn y ot Ha Dc m ce at pt er a ia s l i ig n na th l is of fo 72 rm 0 at p 5 . 0. System Name 32PD5000/42PD5000 32PD5100/42PD5100 32PD5200/42PD5200 READ THE INSTRUCTIONS INSIDE CAREFULLY. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS. The ENERGY STAR® emblem does not represent EPA endorsement of any product or service. [. . . ] · No picture with the power indicating lamp lights in orange. !· Make sure that the switch of the computer, imaging equipment , etc. , is turned on. · Check to see if the input selection matches the connection terminal. · Check to see if the input signal matches the monitor specifications. · Check the way the signal cable is connected. 11 · The message "Invalid Scan Freq. " is displayed. 11 28 29 !Invalid Scan Freq. · The power indicating lamp is normally lit but no picture . · Check the contrast and brightness settings (adjust them for higher contrast and brightness). · Check the way the signal cable is connected. 11 17 · The display image appears flowing slantwise. · Text displayed across the screen appears vertically streaked, with the characters in vertical columns blurred. · The remote control does not work. · Adjust the dot clock frequency and phase. (Adjust the dot clock frequency first, the dot clock phase next. ) (RGB input) 20 26 · Adjust the dot clock phase for the clearest viewing. (RGB input) 20 26 · Check to see if the batteries are loaded in the remote control in opposite direction. · Check to see if the batteries in the remote control are OK. 9 24 Symptom · The temperature of the display panel surface is high. Point to check · The plasma display panel is lighting the phosphors by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. · High-precision technology is used to manufacture the plasma display panel, However in some cases, there are minor defects in some parts of the screen. Please note that this is not a malfunction. See page - · There are locations on the screen that are different from the periphery (*). *Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc. · Vertical stripes appear, depending on the screen contents. - · The plasma display panel is lighting the phosphors by the discharge of internal radiation. Depending on the screen contents, in rare cases this may cause vertical stripes to appear because of failure to light. · Adjusting the Clock Phase will reduce the horizontal stripes. (RGB input) · If the direct frequency from the computer is below 85Hz, try a higher frequency (upper limit 85Hz). · Use the fan that controls the temperature in the main body to lower the temperature of this unit. If the ambient air temperature increases, the fan will start, the RPMs will increase and motor noise will grow louder. [. . . ] Clamp to two or more of the long slotted holes in the upper and lower parts of each wall-mounting metal in a well-balanced manner. cutout 5. Dressing the cables When passing the plasma TV power cord and signal cables behind the plasma TV, use wire clamps, etc. , to prevent cable damage. Mount on a firm, solid surface. Wall-mount metal (top) Wall-mount metal (bottom) Use the washers provided as necessary. Wire clamps Mounting the TV-mount metals on the plasma TV 1. Place a protective sheet cover on the top of a table and place the plasma TV on the cover with the back side upward. [. . . ]