User manual HITACHI 28LD5200E

[. . . ] Colour LCD Monitor Model PW1L 28LD5200E USER'S MANUAL MANUEL UTILISATEUR BEDIENUNGSANLEITUNG READ THE INSTRUCTIONS INSIDE CAREFULLY. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. This monitor is ENERGY STAR® compliant when used with a computer equipped with VESA DPMS. The ENERGY STAR® emblem does not represent EPA endorsement of any product or service. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. NOTE: The information in this manual is subject to change without notice. [. . . ] By using this ability, TruBass gives enhanced bass sound that otherwise would not be heard. This will automatically adjust volume so each channel and input has the same average volume level. The original factory settings for the items of this Menu page can be restored by pressing the OK button. Audio Mode Favourite Treble Bass Balance Suppresses treble. Suppresses left-side sound. SRS TruBass Matrix Surround Perfect Volume Reset Off Low Middle High Off Off (off the function) On On (waiting to reset) TIMER MENU Picture Audio Timer Function Setup Language Select OK Set Timer Off Timer On Timer Select : 30Min. : --:-Return OK MENU P+ Adjust P- Selected characters M M Setup hint This function automatically sets the power to standby status when the indicated time period has elapsed. This automatically sets the power from standby to ON when the indicated time period has elapsed. Input the required time by SELECT buttons on the remote control. Off Timer --Min. 90Min. --(:--) hours (- - : )- minutes On Timer 19 FUNCTION MENU Picture Audio Timer Function Setup Language Select OK Set Function Screen Saver Screen Wipe Black Side Panel Video Power Save Freeze Mode Default Zoom Reset Select Set Off On 60Min. Off Off Split Panoramic Reset Return OK MENU P+ P- P+ P- Function Wide Standard Setting Mode Display ID Number Reset Fill Off 1 Reset Select Set Return 20 M M OPERATING INSTRUCTIONS (continued) ENGLISH Horizontal Position Next / Prev Adjust P+ SETUP MENU MENU P+ P- Picture Audio Timer Function Setup Language Select OK Set P+ OK P- Setup Auto Adjust Horizontal Position Vertical Position Horizontal Clock Clock Phase Reset Select Return Adjust 0 + 31 ­ 20 10 Reset Exit OK 0 Return P+ P- P- Setup Auto Adjust Horizontal Position Vertical Position Horizontal Clock Clock Phase Reset Select Return Adjust 0 + 31 ­ 20 10 Reset Exit OK Clock Phase Next / Prev P+ 10 Adjust Return P- Setup Input Level Frequency Display WVGA Type WXGA Mode Vertical Filter Frequency Mode RGB1 RGB2 Select Set 0. 7V Off Off Off On Movie DVI-PC RGB Return * Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them. M M 21 LANGUAGE MENU Picture Audio Timer Function Setup Language Select OK Set Language OK MENU P+ P- English Français Deutsch Español Italiano Norsk Svenska Select Return Exit Select a language by M L SELECT buttons and press the OK button. OTHER FEATURES Automatic Store Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below. · The previously recorded items will be lost. · The signal mode can be identified by the horizontal/vertical sync frequency and the sync signal polarity. Different signals with which all the elements are the same or similar will be handled as the same signal. 22 OTHER FEATURES (continued) ENGLISH RGB2 RGB H : 48. 4kHz V : 60. 1 Hz OFF ON Signal Check Changes in the signal status are displayed on the screen as they arise. Status The input signal is switched or when the RECALL button is pressed. Display A guide is displayed for the input terminal and the horizontal and vertical sync frequency. Action RGB -- -- Min. -- -- : -- -- When the sync signal is no longer detected. · A guide displays No Sync. Recheck the personal computer Signal, and Power Save (for power switch status and the approx. · When the condition continues where the sync signal cannot be detected, indicator lamp of power source changes in orange and the mode switches to power save mode. Signal When the input signal does not match the monitor specifications or is in an unstable status. 51 52 !Invalid Scan Freq. Power Save Mode When the RGB, RGB2 input is selected · When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the computer is not being used to reduce power consumption by this unit. Horizontal Vertical PC signal Operation mode Indicating lamp Power consumption Yes Yes Active (normal display) On Lights green 155W No Yes Yes No Blank (no display) Off Lights orange 1W or less No No RGB sync signal Returning to operating status · Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control. 23 NOTES About screen defects · High precision technology is used in the making of LCD panels but there may be dark spots (points that do not illuminate) and bright spots (points that are too bright) in some cases. These do not indicate a malfunction. About residual images · In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will disappear and return to normal. This is not a malfunction. About the panel screen · LCD displays display images by illuminating phosphor inside the panel. Because of this, the temperature of the panel surface may rise in some cases. Also, LCD displays are made of finely processed glass, so avoid strong impact because of danger of glass breakage. About using in a low ambient temperature · The response speed of LCD panel becomes slow as ambient temperature falls. [. . . ] (3) Press POWER ON / OFF button. (2) Picture/sound setting set to minimum. (3) TV in standby or power save mode. no picture or sound 48 PRODUCT SPECIFICATIONS ENGLISH · The monitor takes at least 30 minutes to attain the status of optimal picture quality. 49 Signal Input DVI terminal (DVI-D) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Input signal T. M. D. S. Data3+ Pin 14 15 16 17 18 19 20 21 22 23 24 Input signal +5V Power Ground (for+5V) Hot Plug Detect T. M. D. S. Clock- 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Frame GND RGB terminal (D-sub 15-pin connector) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Input signal R (PR/CR) G or sync on green (Y) B (PB/CB) No connection No connection R. GND (PR/CR, GND) G. GND (Y, GND) B. GND (PB/CB, GND) No connection GND No connection [SDA] H. [. . . ]