User manual HASSELBLAD FLEXTIGHT 646

[. . . ] is connected to power. · Do not place your fingers or any other object into the scanner while it · Before servicing or opening the scanner, the power supply must be · Install the scanner in a location where children can not get to it. It is not sufficient simply to press the on/off button. User's Guide - Flextight 646 Hardware Reference - Flextight 646 System Requirements 7 System Requirements Below are the basic hardware requirements for the PC or Macintosh system to which the scanner is to be connected. For information about the processor, operating system, RAM and harddisk requirements please refer to the "Software Reference" manual, that comes with the FlexColor software. · Screen resolution of 800 x 600 pixels with true colors (24-bits). · FireWire interface User's Guide - Flextight 646 English 8 Hardware Reference - Flextight 646 English User's Guide - Flextight 646 Hardware Reference - Flextight 646 Front Panel 9 Front Panel A D E C B Figure 1: Front panel features of Flextight 646 A B C D E Feed Table: place original holders here for scanning. [. . . ] Press the power button (E) on the front of the scanner to switch it on. The button will start flashing green, indicating that no firmware has been downloaded yet. It will be downloaded automatically later when you first run the FlexColor program. The power button (E) will stop flashing indicating that firmware has been downloaded to the scanner. Select the original holder that matches your original: · For transparencies, choose one of the holders (H) that has a square hole in it. · For reflectives, select the large A4/letter-size holder (L) with the clear plastic layer (not included in the standard delivery). Place the original holder with the slotted tab facing into the scanner. For transparency holders (H), the flexible magnetic layer (D) must face upwards and the holder must fit between the guides (C) on both sides of the feed table. For the reflective holder (L), the clear plastic sheet must face upwards. Make sure that the slot (K) in the leading edge of the holder catches the notch (J) in the center of the original holder clasp (F). Slide the holder gently into the original holder clasp (F) at the scanner entrance. resolutions (in ppi) available with each of the original holders when scanning in True Resolutions mode. Original 35 mm Portrait 35 mm Landscape 45 x 60 mm Portrait * 60 x 60 - 60 x 70 mm 4" x 5" Portrait 13 x 18 Portrait * A4 Portrait * Table 1: True Resolutions Max. 6300 5000 4000 3200 2040 1600 960 *) Not included in the standard delivery Calibrating the Scanner The scanner requires two types of calibration: · Focus calibration adjusts the positioning of the scanner's optics for each zoom level. If your scans are coming out unfocused or at slightly the wrong size, then you may need to make a new focus calibration to adjust the zoom mechanism. The focus calibration is stored in the scanner's flash PROM, so it is preserved when you move the scanner to a new computer. During calibration, the scanner scans a white target to establish the white point along the full length of the scanner's CCD. The white calibration is stored in the scanner's flash PROM, so it is preserved when you move the scanner to a new computer. See "White Calibration for Reflectives" on page 22 for more information. · White calibration is only required for reflective scans (it is done Both of the calibration procedures are simple and are initiated from the FlexColor program. User's Guide - Flextight 646 Hardware Reference - Flextight 646 Calibrating the Scanner 21 Focus Calibration The Flextight 646 scanner uses an adjustable zoom and focus mechanism to optimize its scanning resolution for each of the original formats it can handle. If you suspect your scans are not as sharp as they should be, then you may need to calibrate your scanner. It is intended that the scanner is calibrated not more than once every three months. It is a 8 x 9 cm (3" x 3. 5") square of transparent film with a black image on it. Focus sheet PN:40900026, rev. [. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. User's Guide - Flextight 646 English 30 Hardware Reference - Flextight 646 CE - Declaration of Conformity CE - Declaration of Conformity English HASSELBLAD A/S HEJREVEJ 30 DK - 2400 COPENHAGEN NV TELEPHONE +45 7026 0800 TELEFAX +45 7026 0900 REG. /VAT NO. 18635445 www. hasselblad. com Declaration of conformity Application of Council Directives: . . . . . . . . . . . . . . . . . Standards to which Conformity is declared: EN61000-6-1 2001, EN61000-6-3 2001 and EN60950:2000. Manufacturer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hasselblad A/S Hejrevej 30 DK-2400 Copenhagen NV/ Denmark Type of Equipment: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]