User manual GRACO STRAIGHT SHOOTER GUN 9943-1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO STRAIGHT SHOOTER GUN. We hope that this GRACO STRAIGHT SHOOTER GUN user guide will be useful to you.


GRACO STRAIGHT SHOOTER GUN 9943-1: Download the complete user guide (2140 Ko)

You may also download the following manuals related to this product:

   GRACO STRAIGHT SHOOTER GUN 9943-ID (1150 ko)

Manual abstract: user guide GRACO STRAIGHT SHOOTER GUN9943-1

Detailed instructions for use are in the User's Guide.

[. . . ] Manufactured exclusively for: Straight Shooter Gun ® Operating Manual 9943-1 August 26, 2003 Issue 1 GUSMER CORPORATION ® A Subsidiary of Gusmer Machinery Group, Inc. One Gusmer Drive Lakewood, New Jersey, USA 08701-8055 Toll Free 1-800-367-4767 (USA & Canada) Phone: (732) 370-9000 Fax: (732) 905-8968 Copyright 2003, GUSMER CORPORATION ® http://www. gusmer. com NOTICE: This manual contains important information about your GUSMER equipment. Read and retain for future reference. Straight Shooter Gun CONTENTS LIST OF FIGURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CLEAN THE CLOSURE SCREW CAVITIES- With the Gun triggered, remove any particles with a combination of cleaning solvent from the Flush Can, and Clean Out Drills. 3. 4. WARNING: DO NOT RELEASE THE TRIGGER WHILE CLEANING THE CLEAN OUT CLOSURE SCREW CAVITIES WITH THE CLEAN OUT DRILLS. CHECK COMPONENT PRESSURES- Check the Pressure Gauges on the Proportioning Unit of both components to ensure that they are balanced. REPLACE THE CLOSURE SCREWS- Using the 5/16" Spintite replace the Closure Screws. Make sure the screws are tight to insure the integrity of the metal to metal seal. RESUME POURING- 6. 7. 12 9943-1, Issue 1 Operating Manual Servicing Procedure Centerline Component Removal and Service Procedure TOOLS REQUIRED · · · · · · 10" Adjustable Wrench 3/16" Hex Key 1/4" Open End Wrench 5/16" Open End Wrench Cotton Swabs Brass Brush · · · · · 1/2" Open End Wrench 3/8" Open End Wrench 5/16" Spintite Lubriplate Grease or equivalent Clean Out Drills The Center Line Components consist of the following: Figure 6. Centerline Component Removal WARNING: DISCONNECT THE CHEMICAL HOSES AND AIRLINE BEFORE SERVICING THE GUN. IN ADDITION, BE SURE TO CLEAN THE "CENTER LINE COMPONENTS" WITH THE GUN SERVICE KIT PRIOR TO REMOVAL FOR SERVICING AS THEY ARE EXPOSED TO THE CHEMICAL 1. CLOSE BOTH MANUAL VALVES- Using the 5/16" Spintite, turn each Manual Valve fully clockwise. ENGAGE THE SAFETY- Pull the Safety Slide Valve away from the gun to place it in the Safety position. REMOVE MODULE RETAINER- Using the 10" Adjustable Wrench, remove the Module Retainer. LOOSEN THE PACKING NUT- Using the 5/16" Open End Wrench, back out the Packing Nut three or four turns. 13 5. 8/26/03 Straight Shooter Gun NOTE: By removing the Packing Nut entirely the Rear Seal can be removed and replaced. 6. REMOVE THE GUN BLOCK- Using the 3/16" Hex Key, remove the Gun Block Retaining Screw. Carefully slide the Gun Block away from the Valving Rod and Air Cylinder. If dried chemical has built up on the Gun Block removal may be difficult. REMOVE THE VALVING ROD- Using the 1/4" Open End Wrench, on the hex shaped Valving Rod Shank and the 3/8" Open End Wrench on the Jam Nut loosen the Jam Nut by turning it clock wise. (As viewed from the front of the gun. ) Continue to back the Jam Nut away from the Valving Rod Shank by three or four full turns. CLEAN ALL COMPONENTS THOROUGHLY BEFORE REASSEMBLYUsing the appropriate Brass Brushes, Clean Out Drills, etc. When finished, coat the threads and the mating surfaces of the Gun Block, Gun Block Bracket, and Gun with Lubriplate Grease. Do not get any grease in the chemical ports located in the Gun Block or Mixing Module. INSPECT THE GUN BLOCK- It is important to keep the Gun Block clean and free from damage to insure proper operation of the Gun. 7. 8. 9. Centerline Component Installation TOOLS REQUIRED · · 10" Adjustable Wrench 3/16" Hex Key The Center Line Components consist of the following: Figure 7. INSTALL THE VALVING ROD- Thread the Jam Nut as far back on the Piston Rod as possible. [. . . ] Make sure not to loose this spring as it belongs in the hole at the end of the Spool. Replace the O-Rings and apply a thin coat of Lubriplate to the O-Rings REMOVE THE VALVE LINER- Attempt to pull the Valve Liner out of the gun handle through the trigger hole. REMOVE REAR 1/8" HEX NIPPLE- Leaving the Safety Slide Valve and Air Hose in place, use the 6" Adjustable Wrench to remove the 1/8" Hex Nipple. REMOVE THE REAR INTERNAL 1/16" PIPE PLUG- Deeper in the hole that the 1/8" Hex Nipple was removed from locate the 1/16" Pipe Plug. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO STRAIGHT SHOOTER GUN




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO STRAIGHT SHOOTER GUN will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.