User manual GRACO PRO 301 REV A 308-030

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO PRO 301. We hope that this GRACO PRO 301 user guide will be useful to you.


GRACO PRO 301 REV A 308-030: Download the complete user guide (486 Ko)

Manual abstract: user guide GRACO PRO 301REV A 308-030

Detailed instructions for use are in the User's Guide.

[. . . ] OWNER'S MANUAL This manual contains IMPORTANT INSTRUCTIONS and WARNINGS. READ AND RETAIN FOR REFERENCE. 308­030 Rev A PRO 301 Airless Paint Sprayer 1/3 GPM, Electric Model 223­636, Series A 2500 psi (172 bar) MAXIMUM WORKING PRESSURE TABLE OF CONTENTS Warnings . See page 28 to order. FIRE AND EXPLOSION HAZARD Spray painting, flushing or cleaning equipment with flammable liquids in confined areas can result in fire or explosion. Avoid all ignition sources such as static electricity from plastic drop cloths, open flames such as pilot lights, hot objects such as cigarettes, arcs from connecting or disconnecting power cords or turning light switches on and off. [. . . ] Para mantener la continuidad a tierra durante el lavado o descarga de presión, siempre apoyar una parte metálica de la pistola bien firme contra el costado de balde de metal, después apretar el gatillo. Puesta a tierra Para reducir el riesgo de chispas estáticas, conectar a tierra la pulverizadora y todo el otro equipo de pulverizar que se use o se encuentre en el lugar que se va a rociar. CONSULTAR el código eléctrico de la localidad para las instrucciones sobre las conexiones a tierra exigidas para la zona y tipo de equipo. ASEGURAR de conectar a tierra todo este equipo pulverizador: Seguridad durante el lavado Para reducir el riesgo de que se inyecte o salpique fluido en la piel, o que ocurra una descarga de electricidad estática, siempre seguir las INSTRUCCIONES PARA EL LAVADO, dadas en la página 12. Seguir el procedimiento de descarga de presión en la página 6, y quitar la boquilla de metal y usar le presión más baja posible de fluido durante el lavado. 308­030 7 SETUP WARNING To reduce the risk of serious bodily injury caused by static sparking, fluid injection or over­pressurization and rupture of the hose or gun: 1. Be sure all parts added to the sprayer are rated for at least 2500 psi (175 bar) Maximum Working Pressure. Connect a 50 foot spray hose and a gun to the 1/4 npsm(m) fluid outlet nipple. For more flexible gun movement, install a 3 foot (0. 9 m), 3/16 inch ID diameter hose between the gun and main spray hose. Fill the packing nut/wet­cup 1/3 full with Throat Seal Liquid, supplied. DO NOT remove the grounding prong of the plug, and do not use an adapter. Extension cords up to 100 feet (30 m) of 3 wire, 12 gauge (minimum) can be used. CAUTION To avoid damaging the pressure control, follow these precautions. Never use a wire braid hose; it is too rigid to act as a pulsation dampener. Never install any shutoff device between the pressure control and the first 50 feet (15 m) of hose. Plug the power supply cord into an outlet located at least 20 feet (6 m) from the spray area. This reduces the chance of a spark igniting the spray vapors or dust particles. Flush the pump to remove the lightweight test oil which was left in it after factory testing. Strain the paint through a fine nylon mesh bag to remove particles that could clog the spray tip. 8 308­030 SETUP HOSE RACK PACKING NUT/ WETCUP Keep filled with TSL ON/OFF SWITCH SUCTION TUBE STRAINER PRESSURE CONTROL KNOB PRESSURE DRAIN VALVE PUMP 1/4 NPSM(M) FLUID OUTLET DO NOT INSTALL A SHUT OFF DEVICE HERE Fig 1 OPERATION WARNING Pressure Relief Procedure 5. Open the pressure drain valve, having a injection, splashing in the eyes or on the skin, container ready to catch the drainage. injury from moving parts or electric shock, folLeave the pressure drain valve open until low this procedure whenever you shut off the you use the sprayer again. sprayer, check or service any part of the spray system, install, clean or change spray tips, and If you suspect that the spray tip or hose is comor stop the sprayer. pletely clogged, or that pressure has not been fully relieved after following the steps above, 1. Hold a metal part of the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure. 308­030 9 OPERATION ON/OFF SWITCH HOSE RACK SUCTION TUBE STRAINER PRESSURE ADJUSTING KNOB CCW TO LOWER PRESSURE PUMP Fig 2 PRESSURE DRAIN VALVE 1. [. . . ] Toll Free: French Spanish German Greek Korean English 1­800­328­0211 185­955 185­962 186­042 186­046 186­050 185­954 Apply other language in this area on other side of shroud REVERSE-A-CLEANt IV DriplesstTIP GUARD 220­422 Uses fluid pressure from the gun to remove clogs without removing the tip guard to spray tip. (As shown on guns, below. ) Requires SwitchTipt, purchased separately. "SILVER" GUN 220­954 5000 psi (350 bar) MAXIMUM WORKING PRESSURE Includes Reverse­A­Clean IV DripLesst Tip Guard and 517 size SwitchTipt "CONTRACTOR" GUN 220­955 3600 psi (252 bar) MAXIMUM WORKING PRESSURE Includes Reverse­A­Clean IV DripLesst Tip Guard and 517 size SwitchTipt "BLACK MAX" GUN 220­730 3600 psi (252 bar) MAXIMUM WORKING PRESSURE Includes Reverse­A­Clean IV DripLesst Tip Guard and 513 size SwitchTipt DISPLACEMENT PUMP REPAIR KIT 222­587 See contents on page 27. Helps prevent buildup of paint on the rod and throat packings, to reduce premature wear. 1 quart 1 gallon WHEEL KIT 223­822 Converts the PRO301 mounting frame to a portable cart. SPRAY HOSES 223­541 1/4" ID; 50 ft. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO PRO 301




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO PRO 301 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.