User manual GRACO GCP3R4
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO GCP3R4. We hope that this GRACO GCP3R4 user guide will be useful to you.
Manual abstract: user guide GRACO GCP3R4
Detailed instructions for use are in the User's Guide.
[. . . ] Dispense Gun
Probler P2 Elite
For use with non-flammable foam and polyurea. Not for use in explosive atmospheres.
90-110 psi (0. 62-0. 76 MPa, 6. 2-7. 6 bar) Air Inlet Pressure Range 3200 psi (22 MPa, 220 bar) Maximum Static Fluid Pressure
Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.
USER MANUAL
Models: GCP3RA GCP3R0 GCP3R1 GCP3R2 GCP3R3 GCP3R4 GCP3R5
US Patent
6, 796, 461 7, 527, 172
r_gcp3ra_313266_1_1e
Table Of Contents
Section 1 Installation
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] However, if the GlasCraft Probler P2 Elite gun is installed on any other manufacturer's self-designed equipment, great care must be taken to ensure that the maximum static fluid pressure not be exceeded.
If the gun is being used for short periods of spraying, GlasCraft recommends that the purge air be left ON.
11
ON OFF Refer to system manuals for start-up and shut-down procedures.
Section 2 - Operation: Start-Up Instructions
Spray Technique
Always operate safely and follow all safety procedures outlined. To achieve the optimum spray pattern for each application, the appropriate mixing chambers are available in seven sizes. The standard mixing chamber supplied with your gun will be adequate for all but the smallest and largest applications. Foam rise and cure times will vary according to the material and substrate temperature. Higher material or substrate temperature will increase rise and cure times; lower material or substrate temperatures will decrease rise and cure times. Consult your chemical manufacturer's data specification sheets for their recommended spray temperatures. Under most circumstances, both components will be used at identical temperatures. Higher pressures and temperatures may be used to increase material break-up, improve mixing and speed rise times. With hose lengths over 50 ft. (15. 25 m), or when material viscosities are high, higher material pump pressures may be necessary. The gun air valve MUST BE OPENED prior to spraying to provide air for trigger operation and purge air when the trigger is released. When spraying, the gun trigger may be depressed continuously, or triggered at the end of each stroke. A smooth, even layer is best achieved by moving the gun back and forth in a slow, even motion, overlapping the previous pass about 50 to 75 percent. Spraying at an angle to the surface will cause the foam to be rough and will generate overspray.
12
1 Apply permanent thread locker and torque to 35-40 in-lbs (4-4. 5 N·m). 3 Adjust counter-clockwise until it bottoms out.
Part GCP3RA GCP3R0 GCP3R1 GCP3R2 GCP3R3 GCP3R4 GCP3R5
A GC250A GC2500 GC2501 GC2502 GC2503 GC2504 GC2505
B GC251A GC2510 GC2511 GC2512 GC2513 GC2514 GC2515
Kit GC1948 GC1947 GC1947 GC1947 GC1947 GC1949 GC1949
32 44 59 A 17 B 31 14
50 37 49 27
25 47 48
1
65 20 64 46 18 29 39 42 17 28 61 1 23
65c
43 63 54 57
r_gcp3ra_313266_1_2e
26 34 52 58
36
5 4 40 8 38
Section 3 - General Information: P2 Elite Dispense Gun
13
13 41 30 42 39 22 41 12 1
65a
r_257826_313213_1_1b
52 51 45
58
29 19
41 60 13 56
r_gcp3ra_313266_1_4e
3 65f
2 65e
2 65d
1
24
r_gcp3ra_313266_1_3e
65b
Section 3 - General Information: P2 Elite Dispense Gun
10
56
24
12
23
61
53
56
11
62
61
15
21
9
62
14
3
2
r_gcp3ra_313266_1_5e
Section 3 - General Information: P2 Elite Parts List
Ref.
1 2 3 4 5 7I 8 9 10 11 12 I 13 14 15 16 v 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 36 37 38 39 40 41 42 GC0712 GC1198 GC1842 GC2394 GC1880 GC1881 GC1882 GC1883 GC1884 GC1885 GC1886 GC1887 GC1898 GC1899 GC1900 GC1904 GC2494 GC2495 GC1914 GC2499 GC1918 GC1920 GC1921 GC1922 GC1923 GC2496 GC2498 111450 GC0259 GC0275 GC0490 GC0502
Part
GC0024 117634 117635 GC0043 GC0044
Description
PIPE PLUG SWIVEL HOSE FITTING SWIVEL HOSE FITTING O-RING O-RING HEATED HOSE COVER 1/4 IN. BALL FITTING ELBOW FITTING FITTING TUBING, 1000 PSI; NYLON ELBOW FITTING LUBE FITTING BALL VALVE SWIVEL FITTING P2-ELITE HEAD P2 ELITE POLY SIDE BLOCK P2 ELITE ISO SIDE BLOCK PISTON SPACER HOSE MOUNTING PLATE PUSHLOCK SWIVEL ADAPTER WHIP HOSE WHIP HOSE AIR PISTON AIR PISTON CYLINDER SPACER CHECK VALVE FILTER SEAL, ACETAL SEAL HOUSING AIR CAP MACHINED HANDLE TRIGGER PISTON TRIGGER PLUG RETAINING RING SPRING SPRING FILTER SCREEN; 40 MESH 100 MESH FILTER (GC2497) ALSO AVAILABLE SIDE SEAL O-RING
Qty.
3 1 1 2 2 2 2 1 1 1 3 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 2 2 2 2 2
Ref.
43 44 45 46 47 48 49 50 51 52 53 I 54 56 57 58 59 60 61 62 63 64 65
Part
117517 C20988 GC2056 GC2058 108833 107563 GC2059 C20207 GC2060 GC2081 GC2187 GC2212 GC2237 GC2241 GC2244 GC2248 GC2334 GC2337 GC2340 GC2341 258761
Description
O-RING O-RING O-RING O-RING O-RING O-RING O-RING O-RING O-RING SET SCREW HEX NUT; 9/16-27 SCREW FITTING SHOULDER SCREW SET SCREW SET SCREW SCREW FITTING BALL VALVE TRIGGER SPRING PISTON LOCK ASSEMBLY
Qty.
1 1 1 3 1 1 1 1 1 11 2 2 2 1 2 1 4 2 2 1 1 1
Ref. 65a 65b 65c 65d 65e 65f
Part No.
Description AIR CAP STOP SHAFT PISTON STOP COMPRESSION SPRING O-RING ADJUSTMENT NUT
Qty. v Not Shown.
15
Section 3 - General Information: Maintenance
WARNING
Before attempting to perform any maintenance on this gun, relieve All Fluid and Air Pressures!· · · · · · To relieve fluid and air pressures: Turn OFF all air supplies at system except gun trigger air. Trigger the gun until all trigger air pressure has been relieved.
2. Check the material valves, p/n GC2337 for any leaks:
· Turn OFF both material valves.
Perform Gun maintenance as follows: 1. Check for leaking seals (41).
· · · Engage piston lock. · · · · · · Disengage piston lock. [. . . ] If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO GCP3R4
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO GCP3R4 will begin.