Detailed instructions for use are in the User's Guide.
[. . . ] If your installation requires more tubing (4) than supplied, ensure that it is solvent compatible.
System Setup
1. Install air regulators (A) and bleed-type
air shutoff valves (B) in the air line drops for the auto flush control box (C) and solvent pump (D). Control box air inlet pressure must not exceed 100 psi (0. 7 MPa, 7 bar).
2. [. . . ] Connect a short solvent hose (G) between tee and fluid inlet of component B dispense valve (H).
2. Cut four lengths of tubing (4) to connect control box
ON and OFF ports to dispense valve (2) ON and OFF ports. Connect a solvent supply line (J) between solvent
pump outlet and branch of tee.
COMPONENT A SIDE
COMPONENT B SIDE
OFF A SIDE B SIDE
ON OFF
ON
ON
AIR INPUT
ON OFF ON AIR INPUT ON OFF
2
OFF
OFF
4
COMPONENT A ON COMPONENT A OFF COMPONENT B ON COMPONENT B OFF
TI5506a
Detail of Tubing Inside Control Box
TI5505a
4
FIG. Connect Air Lines
4
310800D
Installation
310800D
5
Operation
Operation
WARNING
4. Turn control box component A ON/OFF switch ON.
Component A and component B sides can be flushed simultaneously, if desired.
Read warnings in the ProMix Easy operation manual 309908. Turn control box component B ON/OFF switch ON.
To reduce the risk of fluid injection, which can result in serious injury, including amputation, relieve system pressure as instructed in the proportioner operation manual 309908 before flushing.
7. Disengage trigger lock, and flush through gun until
clean solvent flows. Adjust solvent pump regulator to desired pressure; use lowest pressure possible. Do not exceed the working pressure of the component with the lowest pressure rating.
10. Engage
trigger lock.
6
310800D
Parts
Parts
7* 1* *3 5*
3* 6*, 8*
2
TI5508b
9
TI15359a
Ref. Description 15E932 287222 15E930 buy locally 15E931 104029 110911 222011 155570 TEE, tube fitting VALVE, dispense; see 310655 VALVE, solenoid TUBE; nylon; 4 mm; cut to necessary lengths; not shown CONTROL BOX, bare CLAMP, ground NUT, hex; ground GROUND WIRE UNION, swivel; 1/4 npt(f) x 1/4 npsm(f)
Qty. 1 2 2 30 ft 1 1 1 1 2
*
Parts included in Control Box Kit 15E933.
310800D
7
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]