User manual GRACO 15J755 9-2010

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO 15J755. We hope that this GRACO 15J755 user guide will be useful to you.


GRACO 15J755 9-2010: Download the complete user guide (891 Ko)

Manual abstract: user guide GRACO 15J7559-2010

Detailed instructions for use are in the User's Guide.

[. . . ] 1010. 1-92 for use in Class I Div 1 Group C & D T3 Hazardous locations Read Instruction Manual Warning: Substitution of components may impair intrinsic safety. GRACO INC. Box 1441 Minneapolis, MN 55440 U. S. A. MIN / MAX TEMP RANGE: 0° - 50°C (32° - 122°F) Artwork No. Ci Class I, Division 1, Group C & D T3 Li Hazardous Locations 15 V 60 mA 200 mW 220 nF 280 uH 35 V 200 mA 1. 4 W . 036 uF . 44 uH ti8317b Pressure Relief Procedure Pressure Relief Procedure Kit Installation System pressure can cause the pump to cycle unexpectedly, which could result in serious injury from splashing or moving parts. Open the back pressure regulator and all fluid drain valves in the system, having a waste container ready to catch drainage. [. . . ] Thread the transducer's cable (25a*) through the adapter (42*) and conduit (44*). Torque the adapter (F) first, then the nut (E) to 15-20 ft-lb (21-27 N·m). Reinstall the cover (32*) with two screws (12*). 7 Torque to 15-20 ft-lb (21-27 N·m). 7 *43 *44 58* 7 *42 25a* *41 D FIG. Pressure Transducer ti8721a Pressure Sensor Calibration Information Pressure sensor information (Pr 20. 34, 20. 35, and 20. 36) for your system must be keyed into the Variable Frequency Drive before system start-up. To prevent accidental change of pressure sensor calibration parameters, they are locked by Pr 20. 16. Set Pr 20. 16 to 0 to lock pressure sensor parameters. c. Calibration Parameters from the label: Pr 20. 34 ­ Zero Calibration Pr 20. 35 ­ Calibration Pressure Pr 20. 36 ­ High Calibration 311603C 3 Pressure Sensor Calibration Information 25c* 25b* C 25b* 11 12* 25a* 36* 25c* 33* B ti8725a 35* 44* 11 Torque to 66-78 in-lb (7. 4-8. 8 N·m). FIG. Circuit Board Connections 4 311603C Pressure Transducer Calibration Procedure Pressure Transducer Calibration Procedure E-Flo pressure sensor must be calibrated against an instrument grade High Precision Pressure Transducer, which should be installed near the E-Flo pressure sensor. Ensure that the High Precision Pressure Transducer calibration is up to date. Use Keypad to navigate to Pr 20. 33; monitor its reading for 5 ­ 10 seconds to determine its average value. Navigate to Pr 20. 34 and enter the recorded average value of Pr 20. 33. Keep the system pressurized and ensure that pressure does not fluctuate. Take a pressure reading from the calibration instrument and make a record of it. d. Navigate to Pr 20. 33; monitor its reading for 5-10 seconds to determine its average value. Navigate to Pr 20. 31 and verify that its reading is within the range of 0-3 psi. Verify that reading of Pr 20. 31 is within +/- 2. 5 psi of the system pressure. c. 4. If system is rated to a pressure lower then 250 psi, use maximum allowable rated pressure. Verify that reading of Pr 20. 31 is within +/- 2. 5 psi of the system pressure. 311603C 5 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO 15J755




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO 15J755 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.