User manual GRACO 15H882 SLIDER

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO 15H882 SLIDER. We hope that this GRACO 15H882 SLIDER user guide will be useful to you.


GRACO 15H882 SLIDER : Download the complete user guide (335 Ko)

Manual abstract: user guide GRACO 15H882 SLIDER

Detailed instructions for use are in the User's Guide.

[. . . ] Open the back pressure regulator and all fluid drain valves in the system, having a waste container ready to catch drainage. Check that pressure gauges on fluid supply and return lines read zero. If gauges do not read zero, determine cause and carefully relieve pressure by VERY SLOWLY loosening a fitting. [. . . ] Pull the crank arm/connecting rod/slider piston assembly (CR) up and out of the cylinder. Remove the old bearings (8). 311616B 3 Kit Installation Reassembly 1. The joints between the bearings must align with the pin hole (PH) in the slider piston. 9 12 Place clean rag over slider cylinder (2). Torque key-side screw to 210-230 ft-lb (283-310 N·m) first, then torque gap side screw to 210-230 ft-lb (283-310 N·m). 5 12 38 7 9 8 PH FIG. Position the crank arm (4) to engage the output shaft (OS), and rotate it to the bottom of the output shaft. Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during reassembly. Install the key (39), crank arm cap (38), and cap screws (5), oriented as shown. While the gap-side screw is still loose, torque the key-side screw to 210-230 ft-lb (283-310 N·m). wrench on the flats of the slider piston (9), to keep it from turning when you are tightening the coupling nut (14). Orient the wrench so it is braced against one of the tie rods (3) or the pump stand. Tighten the coupling nut (14) onto the slider piston (9) and torque to 75-80 ft-lb (102-108 N·m). Install Crank Arm Cap 4 311616B Kit Installation Notes 311616B 5 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO 15H882 SLIDER




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO 15H882 SLIDER will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.