User manual GRACO 15H871 REV 9-2010

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO 15H871. We hope that this GRACO 15H871 user guide will be useful to you.


GRACO 15H871 REV 9-2010: Download the complete user guide (927 Ko)

Manual abstract: user guide GRACO 15H871REV 9-2010

Detailed instructions for use are in the User's Guide.

[. . . ] (76 mm) 4 116719 SCREW, 8-32 hex washer head 2 100664 SCREW, set, socket-head; 1/4-20 x 1/2 in. (31 mm) Motor Rotation (counter-clockwise as viewed from fan end) FIG. NEMA 184/182 TC Frame Electric Motors 109* n/a SEAL, input shaft 116* n/a SEAL, output 119* 120395 GASKET, oil plug Parts designated n/a are not available separately. 1 4 1 2 311597C Kit Installation 37* *31 MA 5. 5 shows the cover (32) on the stand side; the motor side cover is (21). [. . . ] wrench, and brace against tie rod (3). 4 32 CR OS 9 ti9225a FIG. Remove the two output seals (116) as follows: 10 12 14 ti9223b a. Remove Coupling Nut (Stand Side Shown) 4 311597C Kit Installation b. Drill 1/8 in. (3 mm) diameter (maximum) pilot holes in the seals (116), using the holes for the sheet metal screws (D) as a template. Install the sheet metal screws (D) through the tool and into the seals (116). Place tape over the output shaft keyway, to prevent damage to the new seals. Place one output seal (116) over the output shaft (OS), with the lips facing in. Place the tool (C) onto the output shaft (OS), fitting one screw (A) into the slot of the shaft. Tighten the screws (G) to lock it onto the shaft. c. D OS c. G d. Install the tool cover (F) and evenly tighten the screws (J) to seat the seal on the output shaft (OS). D G C D 116 f. ti8964a Remove the tools. Take three measurements 120° apart, from the surface of the seal to the face of the housing (H). Remove the tape. 1 4 5 Pack cavity with grease before installing seal. Insert until 116 contacts shoulder. 1 4 1 5 116 109 OS 116 118 ti8963a J F C E H A 1 5 116 119 ti8682a FIG. Position the crank arm (4) to engage the output shaft (OS), and rotate it to the bottom of the output shaft. Place a clean rag over the top of the slider cylinder (2) to prevent debris from falling into the slider assembly during reassembly. Install the key (39), crank arm cap (38), and cap screws (5), oriented as shown. While the gap-side screw is still loose, torque the key-side screw to 210-230 ft-lb (283-310 N·m). Then torque the gap-side screw to 210-230 ft-lb (283-310 N·m). 13. Reinstall the coupler and motor as follows: · To install a NEMA 184/182 TC Frame electric motor, order Motor Coupler Kit 15H880. To install an IEC 112M/B5 or 100L/B5 Frame electric motor, order Motor Adapter Kit 24E453. Slide the coupler into the gear reducer so the key and input shaft mate with the coupler. Apply antiseize lubricant to bore of coupling. · c. d. [. . . ] The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco's sole obligation and buyer's sole remedy for any breach of warranty shall be as set forth above. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO 15H871




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO 15H871 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.