User manual GN NETCOM GN 9050

[. . . ] GN 9050 2. 4 GHz Wireless Headset System Charge battery for 3 hours prior to initial use. User Guide 1 2 3 Components 1 2 3 4 5 Remote Beltpack Base Base Stand Telephone Cord Remote Battery AC Power Adapter Headset (included with System purchase or as an option) 4 5 6 6 7 8 Remote Headset Adapter (Quick Disconnect to 2. 5mm cord adapts your existing headset for remote use-included with non-System purchase) 7 8 1 Remote Beltpack Functions 1 1 2 3 4 2 3 7 6 5 4 Headset/Handset Button/ Optional Handset Lifter Button: Press to enter Headset or Handset Mode as desired (LED on Remote blinks and LED on Base lights in Headset Mode; no lights in Handset Mode). Also for use with optional Remote Handset Lifter; see Remote Handset Lifter user guide for instructions. Setting Up 1. Connect all Cords. 1 Unplug the handset cord from the telephone and plug the Telephone Cord into the vacated handset cord port. [. . . ] If your telephone has volume control, set it at low to mid-range. Using The Remote 12. (45 m) from the Base, remove the Remote from the Base Charger and clip it to your belt. If you move out of range, a tone sounds in your headset every 10 seconds. Calls are not disconnected when out of range, but are, in effect, put on hold. Move back into range to re-establish communications. 4 5 6 7 8 8. Put the Headset on and select a telephone compatibility setting until dial tone is clear. If dial tone is clear for both A and G, set to A. Most phones will require setting A or G. 11. Top: Increase Treble Mid: Neutral Bottom: Increase Bass A B C D E F G 9. Remove the handset and make a call. While switching between the Headset and Handset, adjust the transmit (microphone) setting until your voice is the same volume on both devices (1 is the softest, 8 is the loudest). Disconnect the optional Remote Handset Lifter from the Base while setting the volume. 1 2 3 4 5 6 7 8 A B C Adjusting Remote Beltpack Ring Tone Press the Headset/Handset Button on the Remote to put the system in Handset Mode (the indicator lights on the Remote and Base are not illuminated). Simultaneously press the increase Volume Button (+) as well as the Mute Button for 3 seconds and release. The Headset Mode Indicator light on the remote lights up indicating you are in Ring Setting Mode. Use the Volume Control on the Remote to select one of the four available options: Maximum, Medium, Minimum, Mute. Press + to increase the volume of the ring and press - to decrease or mute the ring tone. Within 10 seconds, the setting will be stored and the Headset Mode Indicator light will go out. 4 5 Frequently Asked Questions What should I check if I don't hear a dial tone?· Make sure that the Headset cord is fully inserted into the Remote. · Make sure that the Battery is properly installed in the Beltpack. [. . . ] · Some telephone systems allow on-hook dialing; refer to your telephone system user guide for instructions. · The number varies greatly due to environmental factors; no specific count can be provided. Accessories Battery To prolong operating time from 6 to 12 hours, an additional Battery can be purchased (GN Netcom part number 1601-809). ReadiLine Remote Handset Lifter with GN ReadiLine Interface Kit The Remote Handset Lifter lifts the handset from your telephone enabling you to answer and hang up calls without returning to your desk. Remote Handset Lifter The Remote Handset Lifter lifts the handset from your telephone enabling you to answer and hang up calls without returning to your desk. 6 7 For more information and technical specifications: www. gnnetcom. com CORPORATE HEADQUARTERS 77 Northeastern Blvd. Nashua, NH · 03062 1-800-826-4656 1-603-598-1100 Fax: 1-603-598-1122 © 2002 GN Netcom, Inc. [. . . ]