User manual GIGABYTE GS-R22PHE ANNEXE 1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GIGABYTE GS-R22PHE. We hope that this GIGABYTE GS-R22PHE user guide will be useful to you.


GIGABYTE GS-R22PHE ANNEXE 1: Download the complete user guide (40366 Ko)

You may also download the following manuals related to this product:

   GIGABYTE GS-R22PHE (40810 ko)
   GIGABYTE GS-R22PHE (1367 ko)
   GIGABYTE GS-R22PHE ANNEXE 2 (40580 ko)
   GIGABYTE GS-R22PHE ANNEXE 3 (21421 ko)

Manual abstract: user guide GIGABYTE GS-R22PHEANNEXE 1

Detailed instructions for use are in the User's Guide.

[. . . ] GS-R22PHL Dual LGA2011 socket motherboard for Intel® Xeon® E5-2600 processors Service Guide Rev. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations:  For detailed product information, carefully read the Serice Guide. For product-related information, check on our website at: http://www. gigabyte. com Preface Before using this information and the product it supports, please read the following general information. [. . . ] • The tray will not fit back into the bay if inserted incorrectly. • Make sure that the HDD is connected to the HDD connector on the backplane. Follow these instructions to install the Hard disk drive: 1. 2. 3. 4. Press the release button. Slide the blank into the bay until it locks into place. 1 2 4 3 4 Hardware Installation - 28 - 2-8 Replacing the FAN Assemblly CAUTION!Before you remove or install the system fan cage, take the steps: • Make sure the system is not turned on or connected to the AC power. Failure to observe these warnings could result in personal injury or damage to the equipment. For GPU12_FAN/GPU34_FANGPU56_FAN/GPU78_FAN/GPU12E_FAN/GPU56E_FAN Follow these instructions to replace the fan assembly: 1. Disconnect fan cable. 3. Reverse the previous step to install the replacement fan assembly. GPU56E_FAN GPU56_FAN GPU12E_FAN GPU78_FAN SYS_FAN2 GPU12_FAN SYS_FAN1 GPU34_FAN 1 CAUTION!• 225W GPGPU Cards x 8 and SATA HDDs x 8 are opeating under 35oC. • 300W GPGPU Cards x 8 and SATA HDDs x 8 are opeating under 30oC. - 29 - Hardware Installation 3 Airflow direction Hardware Installation - 30 - For SYS_FAN1/SYS_FAN2 Follow these instructions to replace the fan assembly: 1. Disconnect fan cable. 3. Reverse the previous step to install the replacement fan assembly. 1 3 Airflow direction - 31 - Hardware Installation For GPU12E_FAN/GPU56E_FAN (Smart Fan) Follow these instructions to replace the fan assembly: 1. 2. 3. 4. Loosen and remove the screws securing the fan cage. Reverse the previous step to install the replacement fan assembly. 1 2 1 1 2 1 3 Airflow direction 4 5 5 5 5 4 Hardware Installation - 32 - CAUTION!• To avoid fan cable damages, please make sure the fan cables are firmly seated in the groove. - 33 - Hardware Installation 2-9 Replacing the Power Supply CAUTION!• In order to reduce the risk of injury from electric shock, disconnect AC power from the power supply before removing it from the system. Follow these instructions to replace the power supply: 1. 2. 3. Disconnect all power cables. Pull up the power supply handle and press the retaining clip on the right side of the power supply along the direction of the arrow. Connect the AC power cord to the replacement power supply. 1 2 3 Hardware Installation - 34 - 3-1 Front View Chapter 3 System Appearance No. 11. Decription Front panel LED and buttons System fan (GPU78_FAN) 2. 5-inch hard disk drive #1 2. 5-inch hard disk drive #2 2. 5-inch hard disk drive #3 2. 5-inch hard disk drive #4 2. 5-inch hard disk drive #5 2. 5-inch hard disk drive #6 2. 5-inch hard disk drive #7 2. 5-inch hard disk drive #8 System fan (GPU34_FAN) - 35 - Hardware Installation 3-2 Rear View 1 2 3 4 5 6 7 8 9 10 11 12 13 14 13 No. 14. Decription System fan (GPU12E_FAN) VGA port Serial port Power swith button ID switch button Reset button (top)/NMI button (buttom) System status LED 10G LAN port 10G LAN port 10/100 Server management LAN port USB 2. 0 ports System fan (GPU56E_FAN) Power supply module cord socket Power supply fan Hardware Installation - 36 - 3-3 Front Panel LED and Buttons 3 4 5 6 7 No. Name Color Green Green N/A Blue N/A Green Green N/A Green Green N/A Green N/A Green 6. System Status LED Amber N/A 1 2 Status Description Solid On System is powered on. System is in ACPI S1 state (sleep mode) • System is not powered on or in ACPI S5 state (power off) Off • System is in ACPI S4 state (hibernate mode) Solid On System identification is active. Network access Disconnect/Idle Network access Disconnect/Idle No HDD access Solid On Link between system and network Blink 1. Power button and LED 2. ID Button and LED LAN1 Activity LED 3. 4. LAN2 Activity LED HDD Activity LED Solid On Link between system and network 5. Solid On HDD access Solid On Running or normal operation Solid On There is at least one sensor that has critical alter. Off System is not ready. Press the button to reset the system. 7. Reset Button CAUTION! • • The HDD LED behavior table above does not apply to SAS add-on card (PCIE_6 slot). [. . . ] Items on this window are non-configurable. - 73 - BIOS Setup 5-5-2 BMC LAN Configuration Lan Channel 1 Configuration Source Select to configure LAN channel parameters statically or dynamically (DHCP). Do nothing option will not modify any BMC network parameters during BIOS phase. Default setting is Dynamic. IP Address(Note) Subnet Mask(Note) Display configured IP Address information. Display configured Subnet Mask information. Default Gateway Address(Note) Display Default Gateway Address information. (Note) The item is configureable when Configuration Source is set to Static. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GIGABYTE GS-R22PHE




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GIGABYTE GS-R22PHE will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.