User manual GIGABYTE GS-R22PDT

[. . . ] These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reason, if a part number change is made, it will not be noted in the printed Service Guide. [. . . ] (Default setting) 2-3 close: Enable BIOS Recovery function. 45 ) CLR_RTC (Clear RTC jumper) 1 1 1-2 close: Normal operation. (Default setting) 2-3 close: Clear RTC status 46 ) PASS_DIS (Skip Supervisor password jumper) 1 1 1-2 Close: Normal operation. (Default setting) 2-3 Close: Clear Supervisor Password in BIOS setup menu. 47 ) BMC_SEL (BMC Selection jumper) 1 1 1-2 Close: Normal operation. (Default setting) 2-3 Close: Enable BMC function. 41 Jumper Setting 48/49 ) JP_STRAP2/ JP_STRAP8 (PilotII firmware upgrade jumper) JP_STRAP2 1 1 1 1 JP_STRAP8 1 Descripeion Boot from BMC BOOT SPI Interface. Boot From internal ROM(Scratchpad Registers) Boot From internal ROM(Scratchpad Registers) 50 ) PILOT_DIS (PilotII Force Mode jumper) 1 1 1-2 close: Normal operation (Default setting) 2-3 close: Disable PilotII device function. 42 GS-R22T61-RH/GS-R22PDT-RH Rack Mount Server Expansion Card Components Description The two riser cards installed in the PCI riser card bracket assembly povides support for both fullheoght and low-profile expansion cards. Full height and low profile PCI Express riser cards SLOT_3 SLOT_2 SLOT_1 SLOT_5 SLOT_4 43 GS-R22T61-RH/GS-R22PDT-RH Rack Mount Server No. 1 2 3 4 5 Code PCI_3 PCI_2 PCI_1 PCI_5 PCI_4 Description PCI express 2. 0 x8 slot (PCI Express 2. 0 x8 throughtput) PCI express 2. 0 x8 slot (PCI Express 2. 0 x8 throughtput) PCI express 2. 0 x8 slot (PCI Express 2. 0 x8 throughtput) PCI express 2. 0 x8 slot (PCI Express 2. 0 x4 throughtput) PCI express 2. 0 x8 slot (PCI Express 2. 0 x8 throughtput) 44 GS-R22T61-RH/GS-R22PDT-RH Rack Mount Server Full-height riser PCI-X riser card (Optional) SLOT_2 SLOT_3 SLOT_1 No. 1 2 3 Code PCI_3 PCI_2 PCI_1 Description PCI- X slot PCI express 2. 0 x8 slot (PCI Express 2. 0 x8 throughtput) PCI express 2. 0 x8 slot (PCI Express 2. 0 x8 throughtput) 45 BIOS Setup BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERINGSETUP When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1". CONTROLKEYS <> <> <> <> <Esc> Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu 46 GS-R22T61-RH/GS-R22PDT-RH Rack Mount Server GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. (Default setting) C2 Disabled Desire state for the Nehalem core C2 state include in the CST as ACPI C2 state. Desire state for the Nehalem core C6 state include in the CST as ACPI C3 56 T State Enabled Disabled CPU C State Enabled Disabled CPU C1E Enabled Disabled C3 OS ACPI C3 Report CPU C6 Report Enabled GS-R22T61-RH/GS-R22PDT-RH Rack Mount Server state. Desire state for the Nehalem core C7 state include in the CST as ACPI C3 state. (Default setting) Disabled Disable CPU C7 Report. CPU C7 Report Enabled Package C State Limit Desired state for the C-State package limit. The default setting is C3 State. ACPI MWAIT extensions Enabled Disabled CST using MWAIT extension isenabled for OSPM use. (Default setting) Disable ACPI MWAIT extensions. 57 BIOS Setup Memory Configuration 58 GS-R22T61-RH/GS-R22PDT-RH Rack Mount Server System Memory/Extended Memory/Memory Frequency/DIMM Status These category is display-only which is determined by POST (Power On Self Test) of the BIOS. Memory Reset Yes Select `Yes', system will clear the memory error status. After rebooting system, the Memory Reset item will set to `No' automatically. (Default setting) Select `Manual" will pops up sub-menu for configuration. (Default setting) No Manual Auto Memory Control Settings Memory RAS Mode Identify the Memory RAS mode. Memory Frequency Select the desire value of Memory frequency. Options available: Auto, DDR-3 800, DDR-3 1066, and DDR-3 1333. Change Interleave setting Change the interleave setting. Options available: 1-way, 2-way, 3-way, 4-way, and 6-way. Rank Interleave setting Configure interleave setting. [. . . ] 0281 Memory Size found by POST differed from CMOS Memory size found by POST differed from CMOS. 02B0 Diskette drive A error 02B1 Diskette drive B error Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the proper diskette type in Setup and that the diskette drive is attached correctly. 02B2 Incorrect Drive A type - run SETUP Type of floppy drive A: not correctly identified in Setup. [. . . ]