User manual GIGABYTE GA-M61PM-S2

[. . . ] 2. 0) AMD Socket AM2 Processor Motherboard User's Manual Rev. 2002 12ME-M61PMS2-2002R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-M61PM-S2 (rev. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. [. . . ] Refer to the following information for diagnosing your LAN cable: When No LAN Cable Is Attached. . . If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will show Open and the Length fields show 0. 0m, as shown in the figure above. If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub, the following message will appear: Start detecting at Port. . . . . Link Detected --> 100Mbps Cable Length= 30m Link Detected Cable Length Displays transmission speed Displays the approximate length of the attached LAN cable. Note: The Gigabit hub will only operate at a speed of 10/100Mbps in MS-DOS mode; it will operate at a normal speed of 10/100/1000Mbps in Windows mode or when the LAN Boot ROM is activated. If a cable problem occurs on a specified pair of wires, the Status field will show Short and the length shown will be the approximate distance to the fault or short. Example: Pair1-2 Status = Short / Length = 1. 6m Explanation: A fault or short might occur at about 1. 6m on Pair 1-2. Note: Pair 4-5 and Pair 7-8 are not used in a 10/100 Mbps environment, their Status fields will show Open, and the length shown is the approximate length of the attached LAN cable GA-M61PM-S2 (rev. 2. 0) Motherboard - 38 - Onboard LAN Boot ROM This function decide whether to invoke the boot ROM of the onboard LAN chip. (Default value) English Onboard Serial Port 1 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled Disabled 378/IRQ7 278/IRQ5 3BC/IRQ7 SPP EPP ECP ECP+EPP BIOS will automatically setup the port 1 address. Using Parallel port as ECP and EPP mode. Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA This option is available only when Parallel Port Mode is set to ECP or ECP+EPP. (Default value) 1 Set ECP Mode Use DMA to 1. On-Chip USB V1. 1+V2. 0 V1. 1 Disabled Enabled Disabled Enabled Disabled Enable the USB 1. 1 and USB 2. 0 controllers. (Default value) USB Keyboard Support USB Mouse Support Legacy USB storage detect This option allows users to decide whether to detect USB storage devices, including USB flash drives and USB hard drives during POST. - 39 BIOS Setup English 2-4 Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Power Management Setup [S1(POS)] [Instant-Off] [Enabled] [Enabled] [Enabled] [Disabled] Everyday 0:0:0 [Disabled] [Disabled] Enter [Soft-Off] Item Help Menu Level ACPI Suspend Type Soft-Off by Power button PME Event Wake Up Modem Ring On USB Resume from Suspend Power-On by Alarm x Day of Month Alarm x Time (hh:mm:ss) Alarm Power On By Mouse Power On By Keyboard x KB Power ON Password AC Back Function : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value) Set ACPI suspend type to S3/STR(Suspend To RAM). Soft-Off by Power button Instant-Off Press power button then Power off instantly. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. (Default value) Modem Ring On An incoming call via modem can awake the system from any suspend state. (Default value) USB Resume from Suspend Disabled Enabled Disable this function. (Default value) Power-On by Alarm You can enable the "Power-On by Alarm" item and key in Date/Time to power on system. Day of Month Alarm : Everyday, 1~31 Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59) Power On By Mouse Disabled Double-Click Disable this function. (Default value) Double click on PS/2 mouse left button to power on the system. 2. 0) Motherboard Power On By Keyboard Disabled Disable this function. (Default value) Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to power on the system. [. . . ] Take out the battery gently and put it aside for about 1 minute (Or you can use a metal object to connect the positive and negative pins in the battery holder to makethem short for 5 seconds). Press Del to enter BIOS and load Fail-Safe Defaults (or load Optimized Defaults). Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?Answer: Please make sure the speaker you are using is equipped with an internal amplifier. [. . . ]