User manual GIGABYTE GA-M57SLI-S4

[. . . ] GA-M57SLI-S4 AMD AthlonTM 64 FX / AthlonTM 64 X2 Dual-Core / AMD AthlonTM 64 / SempronTM AM2 Processor Motherboard User's Manual Rev. 2002 12ME-M57SLI4R-2002R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-M57SLI-S4 Motherboard GA-M57SLI-S4 Apr. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. [. . . ] Pair1-2 Status = Pair3-6 Status = Pair4-5 Status = Pair7-8 Status = Normal Normal Normal Normal / / / / Length Length Length Length = = = = N/A N/A N/A N/A Item Help Menu Level English NV SATA 3 Primary RAID NV SATA 3 Secondary RAID On-Chip IDE Channel0 On-Chip MAC LAN NV Serial-ATA Controller IDE Prefetch Mode Onboard Audio Function SMART LAN : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable. This feature will detect cabling issue and report the approximate distance to the fault or short. Refer to the following information for diagnosing your LAN cable: - 41 - BIOS Setup When LAN Cable Is Functioning Normally. . . If no cable problem is detected on the LAN cable connected to a Gigabit hub, the Status fields of Pair 1-2, Pair 3-6, Pair 4-5, and Pair 7-8 will show Normal and the Length fields will show N/A, as shown in the figure above. If no cable problem is detected on the LAN cable connected to a 10/100 Mbps hub, the Status fields of Pair 1-2 and Pair 3-6 will show Normal and the Length fields will show N/A. However, because Pair 4-5 and Pair 7-8 are not used in a 10/100 Mbps environment, their Status fields will show Short or Open, and the length shown is the approximate length of the attached LAN cable. If a cable problem occurs on a specified pair of wires, the Status field will show Short or Open and the length shown will be the approximate distance to the fault or short. For example, if it shows Pair1-2 Status = Short / Length = 1. 6m, it means that a fault or short might occur at about 1. 6m on Pair 1-2. If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will show Open and the Length fields show 0. 0m. English Onboard 1394 Enabled Disabled Enable onboard IEEE 1394 function. (Default value) Disable onboard IEEE 1394 function. Onboard LAN Boot ROM This function decide whether to invoke the boot ROM of the onboard LAN chip. (Default value) Onboard Serial Port 1 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled Disabled 378/IRQ7 278/IRQ5 3BC/IRQ7 SPP EPP ECP ECP+EPP BIOS will automatically setup the port 1 address. Using Parallel port as ECP and EPP mode. Onboard Parallel Port Parallel Port Mode GA-M57SLI-S4 Motherboard - 42 - ECP Mode Use DMA This item will become available when Parallel Port Mode set to ECP or ECP+EPP. (Default value) 1 Set ECP Mode Use DMA to 1. English On-Chip USB V1. 1+V2. 0 V1. 1 Disabled Enabled Disabled Enabled Disabled Enable USB 1. 1 and USB 2. 0 controllers. (Default value) Enable only USB 1. 1 controller Disable onchip USB support. (Default value) USB Keyboard Support USB Mouse Support Legacy USB storage detect This option allows users to decide whether to detect USB storage devices, including USB flash drives and USB hard drives during POST. (Default value) Disabled Disable this function. - 43 - BIOS Setup English 2-4 Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2007 Award Software Power Management Setup [S1(POS)] [Instant-Off] [Enabled] [Enabled] [Disabled] [Disabled] Everyday 0:0:0 [Enabled] [Disabled] [Disabled] Enter [Soft-Off] Item Help Menu Level ACPI Suspend Type Soft-Off by Power button PME Event Wake Up Modem Ring On USB Resume from Suspend Power-On by Alarm x Day of Month Alarm x Time (hh:mm:ss) Alarm HPET Support (Note) Power On By Mouse Power On By Keyboard x KB Power ON Password AC BACK Function : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value) Set ACPI suspend type to S3/STR(Suspend To RAM). Soft-Off by Power button Instant-Off Press power button then Power off instantly. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. (Default value) Modem Ring On An incoming call via modem can awake the system from any suspend state. (Default value) USB Resume from Suspend Disabled Enabled Disable this function. (Default value) Enable USB device wake up system from suspend mode. (Note) Supported on Windows ® Vista ® operating system only. - 44 - GA-M57SLI-S4 Motherboard Power-On by Alarm You can set "Power-On by Alarm" item to Enabled and key in Date/Time to power on system. [. . . ] Take out the battery gently and put it aside for about 1 minute (Or you can use a metal object to connect the positive and negative pins in the battery holder to makethem short for 5 seconds). Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults). Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?Answer: Please make sure the speaker you are using is equipped with an internal amplifier. [. . . ]