User manual GIGABYTE GA-M55S-S3

[. . . ] 2. 0) AMD Socket AM2 Processor Motherboard User's Manual Rev. 2002 12ME-M55S3R-2002R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-M55S-S3 (rev. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. [. . . ] 2. 0) Motherboard - 42 - 2-6 PC Health Status CMOS Setup Utility-Copyright (C) 1984-2006 Award Software PC Health Status Reset Case Open Status Case Opened Vcore DDR18V +3. 3V +12V Current CPU Temperature Current CPU FAN Speed Current POWER FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning POWER FAN Fail Warning SYSTEM FAN Fail Warning CPU Smart FAN Control (Note) CPU Smart FAN Mode [Disabled] Yes OK OK OK OK 45 oC 3245 RPM 0 RPM 0 RPM [Disabled] [Disabled] [Disabled] [Disabled] [Enabled] [Auto] Item Help Menu Level English : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Reset Case Open Status Disabled Enabled Don't reset case open status. (Default value) Clear case open status at next boot. Case Opened If the case is closed, Case Opened will show "No. " If the case is opened, Case Opened will show "Yes. " If you want to reset Case Opened value, enable Reset Case Open Status and save the change to CMOS, and then your computer will restart. Current Voltage(V) Vcore / DDR18V / +3. 3V / +12V Detect system's voltage status automatically. Current CPU Temperature Detect CPU temperature automatically. Current CPU/POWER/SYSTEM FAN Speed (RPM) Detect CPU/power/system fan speed status automatically. CPU Warning Temperature 60 o C / 140 o F 70 o C / 158 o F 80 o C / 176 o F 90 o C / 194 o F Disabled Disabled Enabled Monitor CPU temperature at 60o C / 140oF. (Default value) Enable CPU/Power/System fan fail warning function. CPU/POWER/SYSTEM FAN Fail Warning - 43 - BIOS Setup English CPU Smart FAN Control (Note) Disabled Enabled Disable this function. When this function is enabled, CPU fan will run at different speed depending on CPU temperature. Users can adjust the fan speed with Easy Tune based on their requirements. (Default value) CPU Smart FAN Mode This option is available only when CPU Smart FAN Control is enabled. Auto BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart FAN control mode for it. (Default Value) Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable. PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable. (Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install. GA-M55S-S3 (rev. 2. 0) Motherboard - 44 - 2-7 MB Intelligent Tweaker(M. I. T. ) CMOS Setup Utility-Copyright (C) 1984-2006 Award Software MB Intelligent Tweaker(M. I. T. ) CPU Frequency (MHz) PCIE Clock (MHz) CPU Clock Ratio DDR2 Voltage Control Chipset/PCIE Voltage HT-Link Voltage CPU HT-Link Voltage CPU Voltage Control Normal CPU Vcore [Auto] [Auto] [Auto] [Normal] [Normal] [Normal] [Normal] [Normal] 1. 3500V Item Help Menu Level English : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Incorrectly using these features may result in system instability or corruption. Doing a overclock or overvoltage on CPU, chipsets and memory modules may result in damages or shortened life expectancy to these components. menu items are for power users only. CPU Frequency (MHz) 200 ~ 500 Set CPU Frequency from 200 MHz to 500 MHz. (Default value: Auto) PCIE Clock (MHz) 100 ~ 200 CPU Clock Ratio This setup option will automatically assign by CPU detection. The option will display "Locked" and read only or will not show up if the CPU ratio is not changeable. DDR2 Voltage Control Please note that by overclocking your system through the increase of the DDR2 voltage, damage to the memory may occur. (Default value) +0. 025V ~ +0. 700V Increase DDR2 voltage by 0. 025V~0. 700V. Chipset/PCIE Voltage Set the voltage settings for chipset and PCI Express bus. (Default value) +0. 025V ~ +0. 375V Increase Chipset/PCIE voltage by 0. 025V~0. 375V. HT-Link Voltage Set the voltage settings for HT-Link. (Default value) +0. 025V ~ +0. 375V Increase HT-Link voltage by 0. 025V~0. 375V. - 45 - BIOS Setup English CPU HT-Link Voltage Set the voltage settings for the HT-Link between CPU and chipset. (Default value) +0. 025V ~ +0. 375V Increase CPU HT-Link voltage by 0. 025V~0. 375V. CPU Voltage Control Please note that by overclocking your system through the increase of the CPU voltage, damage to the CPU or decrease in the CPU life expectancy may occur. (Default value: Normal) Normal CPU Vcore Display your CPU Vcore Voltage. GA-M55S-S3 (rev. 2. 0) Motherboard - 46 - 2-8 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2006 Award Software CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) Esc: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Load Fail-Safe Defaults F11: Save CMOS to BIOS F12: Load CMOS from BIOS Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Fail-Safe DefaultsSave & Exit Setup (Y/N)?N Exit Without Saving English Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) Esc: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Load Optimized Defaults F11: Save CMOS to BIOS F12: Load CMOS from BIOS Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?N Setup Save & Exit Exit Without Saving Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. - 47 - BIOS Setup English 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status MB Intelligent Tweaker(M. I. T. ) Esc: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Change/Set/Disable Password F11: Save CMOS to BIOS F12: Load CMOS from BIOS Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving When you select this function, the following message will appear at the center of the screen to assist you in creating a password. [. . . ] Take out the battery gently and put it aside for about 1 minute (Or you can use a metal object to connect the positive and negative pins in the battery holder to makethem short for 5 seconds). Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults). Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?Answer: Please make sure the speaker you are using is equipped with an internal amplifier. [. . . ]