User manual GIGABYTE GA-H87N-WIFI ANNEXE 1

[. . . ] 2001 12ME-Z87NWIF-2001R Declaration of Conformity We, Manufacturer/Importer, G. B. T. Technology Trading GMbH Address: Product Type: Product Name: Bullenkoppel 16, 22047 Hamburg, Germany Declare that the product Motherboard GA-Z87N-WIFI/GA_H87N-WIFI conforms with the essential requirements of the following directives: 2004/108/EC EMC Directive: Conduction & Radiated Emissions: Immunity: Power-line harmonics: Power-line flicker: 2006/95/EC LVD Directive Safety: 1999/5/EC R&TTE Directive Technical Requirements: EN 300 328 v1. 7. 1 EN 301 489-1 V1. 9. 2, EN 301 489-17 v2. 1. 1 2011/65/EU RoHS Directive Restriction of use of certain substances in electronic equipment: This product does not contain any of the restricted substances listed in Annex II, in concentrations and applications banned by the directive. CE marking EN60950-1:2006+A11:2009+A12:2011 EN 55022:2010 EN 55024:2010 EN 61000-3-2:2006+A2:2009 EN 61000-3-3:2008 Motherboard GA-Z87N-WIFI GA-H87N-WIFI Signature: Timmy Huang Timmy Huang May 20, 2013 (Stamp) Date: May 20, 2013 Name: Wireless Module Country Approvals: See the latest safety and regulatory documents at GIGABYTE's website. Copyright © 2013 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. [. . . ] Password  Set a password with 1~5 characters to turn on the system. Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept. When prompted for the password, press <Enter> again without entering the password to clear the password settings. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. Double Click  Double click on left button on the mouse to turn on the system. && Power On By Keyboard && Power On Password && Power On By Mouse - 53 - BIOS Setup 2-8 Save & Exit && Save & Exit Setup Press <Enter> on this item and select Yes. This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS. Press <Enter> on this item and select Yes to load the optimal BIOS default settings. The BIOS defaults settings help the system to operate in optimum state. Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values. Press <Enter> on the device you select and select Yes to confirm. This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and save as Setup Profile 1~ Setup Profile 8. Or you can select Select File in HDD/USB/FDD to save the profile to your storage device. If your system becomes unstable and you have loaded the BIOS default settings, you can use this function to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS settings. First select the profile you wish to load and then press <Enter> to complete. You can select Select File in HDD/USB/FDD to input the profile previously created from your storage device or load the profile automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked properly (last known good record). && Exit Without Saving && Load Optimized Defaults && Boot Override && Save Profiles && Load Profiles BIOS Setup - 54 - Chapter 3 Configuring SATA Hard Drive(s) RAID Levels RAID 0 Minimum Number of Hard ≥2 Drives Array Capacity Number of hard drives * Size of the smallest drive Fault Tolerance No RAID 1 2 Size of the smallest drive Yes RAID 5 ≥3 (Number of hard drives -1) * Size of the smallest drive Yes RAID 10 ≥4 (Number of hard drives/2) * Size of the smallest drive Yes To configure SATA hard drive(s), follow the steps below: A. B. C. D. Install SATA hard drive(s) in your computer. (Note 2) Before you begin Please prepare: •• At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID, you may prepare only one hard drive. •• A USB thumb drive 3-1 Configuring SATA Controllers A. Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard. Then connect the power connector from your power supply to the hard drive. (Note 1) Skip this step if you do not want to create RAID array on the SATA controller. (Note 2) Required when the SATA controller is set to AHCI or RAID mode. [. . . ] •• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •• Consult a dealer or experienced TV/radio technician for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Neither the Dealer nor the Manufacturer are responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. [. . . ]