User manual GIGABYTE GA-8SRX

[. . . ] The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet. Before you install PCI cards, please remove the Dual BIOS label from PCI slots if there is one. DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) Responsible Party Name: G. B. T. [. . . ] Note that BIOS can not tell from 720 K, 1. 2 M or 1. 44 M drive type as they are all 80tracks. Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. (Default value) Init Display First AGP PCI Set Init Display First to AGP. (Default value) Set Init Display First to PCI. 29 GA-8SRX Motherboard Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Integrated Peripherals IDE1 Conductor Cable IDE2 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE USB Controller USB Legacy Support Onboard Hardware Audio Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode x ECP Mode Use DMA Auto Auto Enabled Enabled Enabled Disabled Enabled 3F8/IRQ4 2F8/IRQ3 Normal Half 378/IRQ7 SPP 3 [ATA33] Set Conductor cable to ATA33 [ATA66/100] Set Conductor cable to ATA66/100 Item Help Menu Level [Auto] Auto-detect IDE cable type : Move Enter:Select +/-/PU/PD:Value F5:Previous Values F10:Save ESC:Exit F1:General Help F6:Fail-Safe Defaults Figure 5: Integrated Peripherals F7:Optimized Defaults 30 BIOS Setup IDE1 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). IDE2 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). On-Chip Primary PCI IDE Enabled Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE Enabled Disabled Enable onboard 2nd channel IDE port. (Default value) Disable onboard 2nd channel IDE port. USB Controller Enabled Disabled Enable USB Controller. (Default value) Disable USB Controller. USB Legacy Support Enabled Disabled Enable USB Legacy Support. (Default value) 31 GA-8SRX Motherboard Onboard Hardware Audio Enabled Disabled Enable Onboard Hardware Audio function. (Default value) Disable this function. Onboard Serial Port 1 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled BIOS will automatically setup the port 1 address. Disable onboard Serial port 1. Onboard Serial Port 2 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled BIOS will automatically setup the port 2 address. Disable onboard Serial port 2. UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) ASKIR IrDA SCR Normal Set onboard I/O chip UART to ASKIR Mode. (Default Value) UR2 Duplex Mode Half Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. 32 BIOS Setup Onboard Parallel port 378/IRQ7 278/IRQ5 Disabled 3BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. Enable onboard LPT port and address is 3BC/IRQ7. Parallel Port Mode SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. Using Parallel port as ECP & EPP mode. ECP Mode Use DMA 3 1 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. 33 GA-8SRX Motherboard Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Power Management Setup ACPI Suspend Type Soft-Off by PWR_BTTN System After AC Back IRQ [3-7, 9-15], NMI ModemRingOn/WakeOnLan PME Event Wake Up Power On by Mouse KB Power On Password Resume by Alarm x Month Alarm x Day (of Month) x Time (hh:nn:ss) S1(POS) Off Off Enabled Enabled Enabled Disabled Enter Disabled NA 0 000 [S3] Set suspend type to Suspend to RAM under ACPI OS Item Help Menu Level [S1] Set suspend type to Power On Suspend under ACPI OS : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: Power Management Setup ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Soft-off by PWR_BTTN Off The user press the power button once, he can turn off the system. [. . . ] Then type the "BIOS flash utility" and "BIOS file" after A:\>. In this case you have to type "A:\> Flash841 7VTX. F4" and then press "Enter". Microsoft(R) Windows98 © Copyright Microsoft Corp 1981-1999 A:\> dir/w Volume in drive A has no label Volume Serial Number is 16EB-353D Directory of A:\ COMMAND. COM 7VTX. F4 FLASH841. EXE 3 file(s) 838, 954 bytes 0 dir(s) 324, 608 bytes free A:\> Flash841 7VTX. F4 (2) Now screen appears the following Flash Utility main menu. Press "Enter", the highlighted item will locate on the model name of the right-upper screen. [. . . ]