User manual GIGABYTE GA-8S648FXM

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch" (show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by SiS® 648FX. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] Enable onboard LPT port and address is 3BC, using IRQ7. Parallel Port Mode This feature allows you to connect with an advanced printer via the port mode it supports. SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as ECP & EPP mode. ECP Mode UseDMA This feature allows you to select Direct Memory Access(DMA) channel if the ECP mode selected. 1 3 Set ECP Mode Use DMA to 1. (Default Value) - 41 - BIOS Setup English Game Port Address This feature allows you to select the game port address or disable it. Disabled 201 209 Disable this function. (Default Value) Set Game port address to 209. Midi Port Address This feature allows you to select the Midi port address or disable it. Disabled 300 330 Disable this function. Set Midi port address to 330. (Default Value) Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) GA-8S648FXM Motherboard - 42 - Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type Soft-Off by PWR_BTTN System After AC Back IRQ [3-7, 9-15], NMI PME Event Wake Up Power On by Keyboard Power On by Mouse Resume by Alarm x Month Alarm x Day (of Month) x Time (hh:mm:ss) Power LED in S1 state : Move [S1(POS)] [Off] [Off] [Enabled] [Enabled] [Disabled] [Disabled] [Disabled] NA 0 0:0:0 [Blinking] ESC:Exit F1:General Help Item Help Menu Level [S1] Set suspend type to Power On Suspend under ACPI OS [S3] Set suspend type to Suspend to RAM under ACPI OS English Enter:Select +/-/PU/PD:Value F10:Save F6:Fail-Safe Defaults F5:Previous Values F7:Optimized Defaults Figure 5: Power Management Setup ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Soft-off by PWR_BTTN Off Suspend User can press Power button to power off system instantly. (Default Value) User can press Power button for 4 seconds to power off system. System will enter suspend mode if button is pressed less than 4 seconds. - 43 - BIOS Setup English System after AC Back Off On Laststate When AC-power back to the system, the system will be in "Off" state. (Default Value) When AC-power back to the system, the system will be in "On" state. When AC-power back to the system, the system will return to the Last state before AC-power off. IRQ [3-7, 9-15], NMI When IRQ[3-7, 9-15] or NMI triggered, the suspend timer will be reloaded to prevent system gets into green mode. (Default Value) Enable PME Event wake up. Power On by Keyboard Any Key Password Set keyboard power on by any key. Input password (from 1 to 8 characters) and press Enter to set the keyboard power on password. (Default Value) Power On by Mouse Disabled Enabled Disable this function. (Default Value) Enable Power On by move or click mouse function. GA-8S648FXM Motherboard - 44 - Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. (Default Value) Enable alarm function to POWER ON system. English If RTC Alarm Lead To Power On is Enabled. Month Alarm : Day (of Month) : Time (hh : mm : ss) : NA, 1~12 1~31 (0~23) : (0~59) : (0~59) Power LED in S1 state Blinking Dual/OFF In standby mode(S1), power LED will blink. If use dual color LED, power LED will turn to another color. - 45 - BIOS Setup English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment [Auto] [Auto] [Auto] Device(s) using this INT: Display Cntrlr -BUS 1 Dev 2 Func 3 : Move Enter:Select +/-/PU/PD:Value F10:Save F6:Fail-Safe Defaults ESC:Exit F1:General Help Item Help Menu Level F5:Previous Values F7:Optimized Defaults Figure 6: PnP/PCI Configurations PCI 1 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 1. PCI 2 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 2. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 2. PCI 3 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 3. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 3. GA-8S648FXM Motherboard - 46 - PC Health Status CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PC Health Status Reset Case Open Status Case Opened Vcore VCC18 +3. 3V +5V +12V Current System Temperature Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning : Move [Disabled] No 1. 778V 1. 856V 3. 2V 4. 945V 12. 288V 33°C 68°C 5113 RPM 0 RPM [Disabled] [Disabled] [Disabled] ESC:Exit F1:General Help [Enabled] Clear case open status at next boot Item Help Menu Level [Disabled] Don't reset case open status English Enter:Select +/-/PU/PD:Value F10:Save Figure 7: PC Health Status F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Reset Case Open Status Case Opened If the case is closed, "Case Opened" will show "No". If the case have been opened, "Case Opened" will show "Yes". [. . . ] Integrated Peripherals--> Onboard H/W Serial ATA: "enable" Then it depends on the SATA mode that you need to set "RAID" to RAID mode or "BASE" to normal ATA mode in the item named Serial ATA function. Question 12: For the M/B which have RAID function, how to set in the BIOS in order to bootup from IDE3, 4 by either RAID or ATA mode?Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. [. . . ]