User manual GIGABYTE GA-8S648

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by SiS® 648. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] Set Midi Port Address to 330. (Default Value) Disable this function. CMidi Port IRQ 85 810 Set Midi Port IRQ to 5. (Default Value) GA-8648(-L) Motherboard - 40 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Soft-Off by PWR_BTTN Sy stem After AC Back IRQ [3-7, 9-15], NMI ModemRingOn PME Ev ent Wake Up Pow er On by Key board Pow er On by Mouse Resume by Alarm x Month Alarm x Day (of Month) x Time (hh:mm:ss) Pow er LED in S1 state higf: Mov e [S1(POS)] [Off] [Off] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] [Disabled] NA 0 000 [Blinking] Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] Set suspend ty pe to Pow er On Suspend under ACPI OS F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Soft-off by PWR_BTTN 8Off The user press the pow er button once, he can turn off the sy stem. (Default Value) 8Suspend The user press the pow er button once, then he can enter suspend mode. C System after AC Back 8LastState When AC-pow er back to the sy stem, the sy stem w ill return to the Last state before AC-pow er off. 8Off When AC-pow er back to the sy stem, the sy stem w ill be in "Off" state. (Default Value) 8On When AC-pow er back to the sy stem, the sy stem w ill be in "On" state. - 41 BIOS Setup English C IRQ [3-7, 9-15], NMI 8Disabled 8Enabled Disable this function. (Default v alue) C ModemRingOn 8Disabled 8Enabled Disable Modem Ring on function. (Default Value) C PME Event Wake Up 8Disabled 8Enabled Disable this function. (Default Value) C Power On by Keyboard 8Passw ord Input passw ord (from 1 to 8 characters) and press Enter to set the Key board Pow er On Passw ord. (Default Value) CPower On by Mouse 8Enabled 8Disabled Enable Pow er On by Mouse function. (Default Value) C Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to pow er on sy stem. (Default Value) Enable alarm function to POWER ON sy stem. If RTC Alarm Lead To Pow er On is Enabled. Month Alarm : Day (of Month) : Time ( hh: mm: ss) : NA, 1~12 1~31 (0~23) : (0~59) : (0~59) C Power LED i n S1 state 8Blinking 8Dual/OFF In standby mode(S1), pow er LED w ill blink. GA-8648(-L) Motherboard - 42 - English PnP/PCI Configurations CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are PnP/PCI Configurations PCI 4 IRQ Assignment PCI 1/5 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e F6:Fail-Safe Defaults ESC:Ex it F1:General Help F5:Prev ious Values F7:Optimized Defaults Figure 6: PnP/PCI Configurations C PCI 4 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 4. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 4. C PCI 1/5 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1/5. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 1/5. C PCI 2 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 2. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 2. C PCI 3 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 3. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 3. - 43 - BIOS Setup English PC Health Status CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are PC Health Status Reset Case Open Status Case Opened VCORE VCC18 +3. 3V +5V +12V Current Sy stem Temperature Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning higf: Mov e [Disabled] No 1. 778V 1. 856V 3. 2V 4. 945V 12. 288V 33°C 45°C 5113 RPM 0 RPM [Disabled] [Disabled] [Disabled] ESC:Ex it F1:General Help [Enabled] Clear case open status at nex t boot Item Help Menu Lev el u [Disabled] Don' reset case t open status Enter:Select +/-/PU/PD:Value F10:Sav e F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 7: PC Health Status C Reset Case Open Status C Case Opened If the case is closed, "Case Opened" w ill show "No". If the case hav e been opened, "Case Opened" w ill show "Yes". If y ou w ant to reset "C ase Opened" v alue, set "Res et Case Open Status" to "Enabled" and sav e CMOS, y our computer w ill restart. C Current Voltage (V) VCORE / VCC18 / +3. 3V / +5V / +12V 8Detec t sy stem' s v oltage status automatic ally . GA-8648(-L) Motherboard - 44 - C Current System / CPU Temperature 8Detec t Sy stem /CPU temperature automatic ally . English C Current CPU/SYSTEM FAN Speed (RPM) 8Detec t CPU/Sy stem Fan speed status automatic ally . C CPU Warning Temperature 8Disabled 860°/140°F 870°/158°F 880°/176°F 890°/194°F Don't monitor CPU's temperature. (Default v alue) Alarm w hen CPU current temperature ov er than 60°/140°F. [. . . ] Advanced BIOS features--> SATA/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W Serial ATA: "enable" Then it depends on the SATA mode that you need to set "RAID" to RAID mode or "BASE" to normal ATA mode in the item named Serial ATA function. - 77 Appendix English Question 12:For the M/B which have RAID function, how to set in the BIOS in order to bootup from IDE3, 4 by either RAID or ATA mode?Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. [. . . ]