User manual GIGABYTE GA-8PEMT4

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X(1. 5V). Caution: AGP 2X(3. 3V) card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). Please insert an AGP 4X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X (1. 5V) mode by adjusting the jumper. [. . . ] (Default v alue) Disable USB Controller. C USB Keyboard Support 8Enabled 8Disabled Enable USB Key board Support. (Default v alue) C USB Mouse Support 8Enabled 8Disabled Enable USB Mouse Support. (Default v alue) C AC97 Audio 8Auto 8Disabled Enable onboard AC'97 audio function. (Default Value) Disable this function. C Onboard H/ W LAN (*) 8Enabled 8Disabled Enabled Onboard LAN function. (Default v alue) Disabled onboard LAN function. C Onboard LAN Boot ROM (*) 8Enabled Enabled Onboard LAN Boot ROM function. 8Disabled Disabled onboard LAN Boot ROM function. (Default v alue) GA-8PEMT4 Series Motherboard - 32 - C Onboard Serial Port 1 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS w ill automatically setup the port 1 address. Disable onboard Serial port 1. English C Onboard Serial Port 2 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS w ill automatically setup the port 2 address. Disable onboard Serial port 2. C UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) 8ASKIR 8IrDA 8Normal Set onboard I/O chip UART to ASKIR Mode. (Default Value) C UR2 Dupl ex Mode 8Half 8Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. C Onboard Parallel port 8378/IRQ7 8278/IRQ5 8Disabled 83BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. Enable onboard LPT port and address is 3BC/IRQ7. CParallel Port Mode 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port. - 33 BIOS Setup English CECP Mode Use DMA 83 81 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. Disable this function. CMidi Port Address 8300 8330 8Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. CMidi Port IRQ 85 810 Set Midi Port IRQ to 5. (Default Value) FCIR Port Address This feature allow s y ou to select CIR port address or disable it. Enabled CIR and Address is 320. FCIR Port IRQ (When Parallel Port Mode is set [ECP or ECP+EPP]) This feature allows you to select CIR IRQ , if CIR is enabled. 85 811 CIR use IRQ 5. (Default Value) GA-8PEMT4 Series Motherboard - 34 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Soft-Off by PWR_BTTN PME Ev ent Wake Up ModemRingOn/WakeOnLan Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Alarm Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function S1(POS) Instant-Off Enabled Enabled Disabled Ev ery day 000 Disabled Disabled Enter Soft-Off [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Set suspend ty pe to Pow er On Suspend under ACPI OS Item Help Menu Lev el u [S1] higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F5:Prev ious Values F6:Fail-Safe Defaults F1:General Help F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type This option will not be shown or not be available if you are using a CPU with the locked ratio. 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Soft-off by PWR_BTT N 8Instant-off 8Delay 4 Sec. Enter suspend if button is pressed less than 4 sec. C PME Event Wake Up 8Disabled 8Enabled Disable this function. (Default Value) - 35 BIOS Setup English FModem Ring On/ WakeOnLAN (When AC Back Function is set to [S oft-Off]) MYou can enable w ake on LAN feature by the "ModemRingOn/WakeOnLAN" or "PME Ev ent Wake up" w hen the M/B has "WOL" onboard connector. Only enabled the feature by "PME Ev ent Wake up". M An incoming call v ia modem aw akes the sy stem from its soft-off mode. [. . . ] STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In", and the Center/Subw oofer channels to "MIC In " . Line Out Line In MIC In English STEP 2 : After installation of the audio driv er, you ` find an ll icon on the taskbar' status area. Click the audio icon s "Sound Effect" from the w indow s tray at the bottom of the screen. STEP 3 : Select "Speaker Configuration", and choose the "6 channels for 5. 1 speakers out put". Dis able "Only SURROUND-KIT"and pess " OK" - 69 - Technical Reference English Advanced 6 Channel Analog Audio O utput Mode (using Audio Combo Kit, Optional Dev ice): (Audio Combo Kit provides SPDIF output port : optical & coaxis and SURROUND-KIT : Rear R/L & Center/subwoofer) SURROUND-KIT access analog output to rear channels and Center/Subw oofer channels. [. . . ]