User manual GIGABYTE GA-8PE800 PRO

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X(1. 5V). Caution: AGP 2X(3. 3V) card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). Please insert an AGP 4X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X (1. 5V) mode by adjusting the jumper. [. . . ] C Don'monitor current temperature. (Default v alue) t F Fan Fail Warning ( CPU / POWER / SYSTEM) 8Disabled 8Enabled Fan Fail Alarm Function Disabled. (Default v alue) Fan Fail Alarm Function Enabled. GA-8PE800 Ultra / Pro(-R) Motherboard - 54 - English Frequency/Voltage Control CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Software Frequency/Voltage Control CPU Clock Ratio CPU Host Clock Control øCPU Host Frequency (MHz) øFix edPCI/AGP Frequency Host/ DRAM Clock ratio Memory Frequency (MHz) PCI/ AGPFrequency (MHz) DIMM Ov erVoltage Control AGP Ov erVoltage Control CPU Voltage Control Normal CPU Vcore [ 15X] [Disable] 100 33/66 [Auto] 266 33/66 [Normal] [Normal] [Normal] 1. 4750V Item Help Menu Lev el u Set CPU Ratio if CPU Ratiois unlocked. higf: Mov e Enter:Select +/-/PU/PD:Value F10:Save ESC:Ex it F1:General Help F3:Language F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 8: Frequency /Voltage Control øThose items will be available when "CPU Host Clock Control" is set to Enabled. CCPU Cl ock Ratio This setup option will automatically assign by CPU detection. For Willamette CPU: 8X~23X default: 14X For C-Stepping P4: 8X, 10X~24X default: 15X For Northwood CPU: 12X~24X default: 16X The option w ill display "Locked" and read only if the CPU ratio is not changeable. F CPU Host Clock Control Note: If sy stem hangs up before enter CMOS setup utility , w ait for 20 sec for times out reboot . When time out occur, sy stem w ill reset and run at CPU default Host clock at nex t boot. 8Disable 8Enable Disable CPU Host Clock Control. (Default v alue) Enable CPU Host Clock Control. - 55 - BIOS Setup English F CPU Host Frequency (MHz) 8100MHz ~ 355MHz Set CPU Host Clock from 100MHz to 355MHz. F Fi xed PCI/AGP Frequency 8You can choose those mode to adjust PCI/AGP frequency. (Select PCI/AGP frequency asy nchronous w ith CPU frequency ). F Host/DRAM Cl ock Ratio for FSB(Front Side Bus) frequency =400MHz, 82. 0 82. 66 8Auto Memory Frequency = Host clock X 2. 0. (Default v alue) for FSB(Front Side Bus) frequency =533MHz, 82. 0 Memory Frequency = Host clock X 2. 0. (Default v alue) for FSB(Front Side Bus) frequency =667MHz, 82. 0 Memory Frequency = Host clock X 2. 0. (Default v alue) FMemory Frequency(Mhz) 8The v alues depend on CPU Host Frequency(Mhz) . F PCI/AGP Frequency(Mhz) 8The v alues depend on Fixed PCI/AGP Frequency item. F DIMM OverVoltage Control 8Normal 8+0. 1V~+0. 2V The default DIMM v oltage. (Default v alue) Set DIMM v oltage from 2. 6V~2. 7V. F AGP OverVoltage Control 8Normal 8+0. 1V~+. 03V Auto detect AGP v oltage. (Default v alue) Set AGP v oltage from 1. 6V~1. 8V. F CPU OverVoltage Control 8Normal Auto detect CPU v oltage. (Default v alue) 80. 8375V~1. 600V Set CPU v oltage from 0. 8375V~1. 600V. FNormal CPU Vcore 1. 4 750V GA-8PE800 Ultra / Pro(-R) Motherboard - 56 - English Top Performance CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Software }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status Select Language Load Fail-Safe Defaults Load Optimiz ed Defaults Load Top Performance Defaults SetSuperv is or Password SetUser Password Sav e & Ex it Setup Ex it Without Sav ing ENTER: Accept F3:ChangeLanguage F10:Sav e & Exit Setup Disabled. . . . . . . . . . . . . . . . . . . [ n Enabled. . . . . . . . . . . . . . . . . . . [ ] ] }Frequency/Voltage Control Top Performance hi: Mov e ESC:Quit ESC: Abort F8:Dual BIOS /Q-Flash Figure 9: Top Performance Top Performance If you wish to maximize the performance of your system, set "Top Performance" as "Enabled". 8Disabled 8Enabled Disable this function. (Default Value) Enable Top Performance function. M "Top Performance" w ill increase H/W working speed. Different sy stem configuration (both H/W component and OS) w ill effect the result. For ex ample, the same H/W configuration might not run properly w ith Window s XP, but w orks smoothly w ith Window s NT. Therefore, if y our sy stem is not perform enough, the reliability or stability problem w ill appear sometimes, and w e w ill recommend y ou disabling the option to av oid the problem as mentioned abov e. - 57 - BIOS Setup English Select Language CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Software }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations u Select Language Load Fail-Safe Defaults Load Optimiz ed Defaults SetSuperv is or Password SetUser Password Sav e & Ex it Setup Ex it Without Sav ing }PC Health Status }Frequency/Voltage Control Top Performance ESC:Quit F8:Dual BIOS /Q-Flash F3:ChangeLanguage F10:Sav e & Exit Setup Figure 10:Select Language Select Lang uage Multi Language is supports 7 languages. There are English, Japanese, French, Spanish, Germany, Simplified C hinese, Traditional Chinese. GA-8PE800 Ultra / Pro(-R) Motherboard - 58 - English Load Fail-Safe Defaults CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Software }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status Select Language Load Fail-Safe Defaults Load Optimiz ed Defaults SetSuperv is or Password SetUser Password Sav e & Ex it Setup Load FailFigure 11: Load Fail-Safe Defaults }Frequency/Voltage Control Safe D efaults?(Y/N)?N Sav ing Ex it Without Top Performance ESC:Quit F8:Dual BIOS /Q-Flash F3:ChangeLanguage F10:Sav e & Exit Setup Load Fail-Safe Defaults Figure 11: Load Fail-Safe Defaults F Load Fail-Safe Defaul ts Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum sy stem performance. - 59 - BIOS Setup English Load Optimized Defaults CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Software }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup Select Language Load Fail-Safe Defaults Load Optimiz ed Defaults SetSuperv is or Password }PnP/PCI Configurations SetUser Password Load Optimized D Sav e (Y/N )?N Figure 11: Load Fail-Safe Defaults efaults?& Ex it Setup }PC Health Status }Frequency/Voltage Control Top Performance ESC:Quit F8:Dual BIOS /Q-Flash F3:ChangeLanguage F10:Sav e & Exit Setup Load Optimiz ed Defaults Figure 12: Load Optimized Defaults Ex it Without Sav ing F Load Optimized Defaul ts Selecting this field loads the factory defaults for BI OS and Chipset Features which the system automatically detects. GA-8PE800 Ultra / Pro(-R) Motherboard - 60 - English Set Supervisor/User Password CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Software }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status Enter Passw ord: Figure 11: Load Fail-Safe Defaults }Frequency/Voltage Control Top Performance ESC:Quit F8:Dual BIOS /Q-Flash F3:ChangeLanguage F10:Sav e & Exit Setup Change/Set/Dis ablePassword Figure 13: Passw ord Setting Select Language Load Fail-Safe Defaults Load Optimiz ed Defaults SetSuperv is or Password SetUser Password Sav e & Ex it Setup Ex it Without Sav ing When you select this function, the following message will appear at the center of the screen to assist you in creating a password. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. [. . . ] Please refer to the user manual and check whether you have connected any cable that is not provided with the motherboard package to the USB Over Current pin in the Front USB Panel. If the cable is your own cable, please remove it from this pin and do not connect any of your own cables to it. English GA-8PE800 Ultra / Pro(-R) Motherboard - 100 - Question 10: Sometimes I hear different continuous beeps from computer after system boots up. Answer: The beep codes below may help you identify the possible computer problems. gAMI BIOS Beep Codes *Computer gives 1 short beep when system boots successfully. [. . . ]