User manual GIGABYTE GA-8IR533

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Do not use AGP 2X card (3. 3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845(E/G) / 850(E) chipset can't support AGP 2X(3. 3V). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/ 4X mode AGP slot. [. . . ] Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE dev ice and cable is compatible w ith ATA33). C IDE2 Conductor Cable 8Auto 8ATA66/100 8ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure y our IDE dev ice and cable is compatible w ith ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE dev ice and cable is compatible w ith ATA33). C USB Controller 8Enabled 8Disabled Enable USB Controller. (Default v alue) Disable USB Controller. C USB Keyboard Support 8Enabled 8Disabled Enable USB Key board Support. (Default v alue) 32 BIOS Setup C USB Mouse Support 8Enabled 8Disabled Enable USB Mouse Support. (Default v alue) FAC97 Audio 8Auto 8Disabled Enable onboard AC'97 audio function. (Default Value) Disable this function. C Onboard Serial Port 1 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS w ill automatically setup the port 1 address. Disable onboard Serial port 1. C Onboard Serial Port 2 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS w ill automatically setup the port 2 address. Disable onboard Serial port 2. C UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) 8ASKIR 8IrDA 8Normal Set onboard I/O chip UART to ASKIR Mode. (Default Value) 33 GA-8IR533 Series Motherboard C UR2 Dupl ex Mode 8Half 8Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. C Onboard Parallel port 8378/IRQ7 8278/IRQ5 8Disabled 83BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. Enable onboard LPT port and address is 3BC/IRQ7. CParallel Port Mode 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port. Using Parallel port as ECP & EPP mode. CECP Mode Use DMA 83 81 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. Disable this function. CMidi Port Address 8290 8300 8330 8Disabled Set Midi Port Address to 290. Set Midi Port Address to 330. (Default Value) Disable this function. 34 BIOS Setup CCIR Port Address 8310 8320 8Disabled Set CIR Port Address to 310. Disable this function. CCIR Port IRQ 85 811 Set CIR Port IRQ to 5. (Default Value) 35 GA-8IR533 Series Motherboard Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Pow er LED in S1 state Soft-Off by PWR_BTTN ModemRingOn PME Ev ent Wake Up Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function S1(POS) Blinking Instant-Off Enabled Enabled Disabled Ev ery day 000 Disabled Disabled Enter Soft-Off Set suspend ty pe to Pow er On Suspend under ACPI OS [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Power LED i n S1 state 8Blinking 8Dual/Off In standby mode(S1), pow er LED w ill blink. If use dual color LED, pow er LED w ill turn to another color. 36 BIOS Setup C Soft-off by PWR_BTT N 8Instant-off 8Delay 4 Sec. Enter suspend if button is pressed less than 4 sec. C PME Event Wake Up 8Disabled 8Enabled Disable this function. (Default Value) FModemRingOn 8Disabled 8Enabled Disable Modem Ring On / Wake On LAN function. [. . . ] (1) After the system boot from floppy disk, type "A:\> dir/w" and press "Enter" to check the entire files in floppy A. Then type the "BIOS flash utility" and "BIOS file" after A:\>. In this case you have to type "A:\> Flash841 7VTX. F4" and then press "Enter". Microsoft(R) Windows98 © Copyright Microsoft Corp 1981-1999 A:\> dir/w Volume in drive A has no label Volume Serial Number is 16EB-353D Directory of A:\ COMMAND. COM 3 file(s) 0 dir(s) 7VTX. F4 FLASH841. EXE 838, 954 bytes 324, 608 bytes free A:\> Flash841 7VTX. F4 (2) Now screen appears the following Flash Utility main menu. [. . . ]