User manual GIGABYTE GA-8IPE775 PRO

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/ G) / 850(E) / E7205 / 865(G/PE/P) / 875P. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 3. PCI 4 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 4. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 4. - 45 - BIOS Setup English PC Health Status CMOS Setup Utility-Copyright (C) 1984-2004 Award Software PC Health Status Reset Case Open Status Case Opened Vcore DDR25V +3. 3V +12V Current CPU Temperature Current CPU FAN Speed Current POWER FAN Speed 1 Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning POWER FAN Fail Warning 1 SYSTEM FAN Fail Warning CPU Smart FAN Control 12 [Disabled] Yes OK OK OK OK 50oC 4687 RPM 0 RPM 0 RPM [Disabled] [Disabled] [Disabled] [Disabled] [Enabled] Item Help Menu Level [Disabled] Don't monitor current fan speed [Enabled] Clear case open status and set to be Disabled at next boot : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Save Default F10: Save ESC: Exit F7: Optimized Defaults F1: General Help Reset Case Open Status Disabled Enabled Don't reset case open status. (Default value) Clear case open status at next boot. Case Opened If the case is closed, "Case Opened" will show "No". If the case have been opened, "Case Opened" will show "Yes". If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save CMOS, your computer will restart. Current Voltage (V) Vcore / DDR25V / +3. 3V / +12V Detect system's voltage status automatically. Current CPU Temperature Detect CPU Temp. automatically. Current CPU/POWER /SYSTEM FAN Speed (RPM) Detect CPU/POWER/SYSTEM Fan speed status automatically. Only for GA-8IPE775 Pro. Only for GA-8IPE775-G. GA-8IPE775 Series Motherboard - 46 - CPU Warning Temperature 60 oC / 140 o F 70 oC / 158 o F 80 C / 176 F 90 oC / 194 o F Disabled o o English Monitor CPU Temp. (Default value) CPU FAN Fail Warning Disabled Enabled Fan Warning Function Disable. (Default value) Fan Warning Function Enable. POWER FAN Fail Warning Disabled Enabled Fan Warning Function Disable. (Default value) Fan Warning Function Enable. SYSTEM FAN Fail Warning Disabled Enabled Fan Warning Function Disable. (Default value) Fan Warning Function Enable. CPU Smart FAN Control Disabled Enabled Disable this function. When the CPU temperature is higher than 70 degrees Celsius, CPU fan will run at full speed. When the CPU temperature is between 50 and 70 degrees Celsius, CPU fan will run at high speed. When the CPU temperature is between 40 and 50 degrees Celsius, CPU fan will run at medium speed. When the CPU temperature is lower than 40 degrees Celsius, CPU fan will run at low speed. Only for GA-8IPE775 Pro. Only for GA-8IPE775-G. - 47 BIOS Setup English Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Frequency/Voltage Control CPU Clock Ratio CPU Host Clock Control x CPU Host Frequency (Mhz) x AGP/PCI/SRC Fixed Memory Frequency For Memory Frequency (Mhz) AGP/PCI/SRC Frequency (Mhz) DIMM OverVoltage Control AGP OverVoltage Control CPU Voltage Control Normal CPU Vcore [15X] [Disabled] 100 66/33/100 [Auto] 266 66/33/100 [Normal] [Normal] [Normal] 1. 3875V Item Help Menu Level : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Save Default F10: Save ESC: Exit F7: Optimized Defaults F1: General Help Incorrect using these features may cause your system broken. For power End-User use only! CPU Clock Ratio This option will not be shown or not be available if you are using a CPU with the locked ratio. The option will display "Locked" and read only if the CPU ratio is not changeable. CPU Host Clock Control Please note that if your system is overclocked and cannot restart, please wait 20secs. for automatic system restart or clear the CMOS setup data and perform a safe restart. (Default value) Enable CPU Host Clock Control. CPU Host Frequency (Mhz) This item will be available when "CPU Host Clock Control" is set to Enabled. If you use FSB400 Pentium 4 processor, please set "CPU Clock" to 100MHz. If you use FSB533 Pentium 4 processor, please set "CPU Clock" to 133MHz. If you use FSB800 Pentium 4 processor, please set "CPU Clock" to 200MHz. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]