User manual GIGABYTE GA-8IG1000-G

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] When the CPU temperature is between 50 and 60 degrees Celsius, CPU fan will run at high speed. When the CPU temperature is between 40 and 50 degrees Celsius, CPU fan will run at medium speed. When the CPU temperature is lower than 40 degrees Celsius, CPU fan will run at low speed. () * For GA-8IG1000 Pro-G only. - 52 - GA-8IG1000 Series Motherboard English Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Frequency/Voltage Control CPU Clock Ratio CPU Host Clock Control CPU Host Frequency(Mhz) AGP/PCI/SRC Fixed Memory Frequency For Memory Frequency(Mhz) AGP/PCI/SRC Frequency(Mhz) AGP OverVoltage Control DIMM OverVoltage Control CPU Voltage Control Normal CPU Vcore [15X] [Disabled] 100 66/33100 [Auto] 266 66/33100 [Auto] [Auto] [Auto] 1. 4750V Item Help Menu Level : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F3: Language (*) F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Figure 8: Frequency/Voltage Control Those items will be available when "CPU Host Clock Control" is set to Enabled. CPU Clock Ratio This option will not be shown or not be available if you are using a CPU with the locked ratio. For C-Stepping P4: 8X, 10X~24X default: 15X For Northwood CPU: 12X~24X default: 16X The option will display "Locked" and read only if the CPU ratio is not changeable. () * For GA-8IG1000 Pro-G only. - 53 BIOS Setup English CPU Host Clock Control Note: If system hangs up before enter CMOS setup utility, wait for 20 sec. When time out occur, system will reset and run at CPU default Host clock at next boot. Disabled Enabled Disable CPU Host Clock Control. (Default value) Enable CPU Host Clock Control. CPU Host Frequency 100MHz ~ 355MHz Set CPU Host Clock from 100MHz to 355MHz. If you use FSB400 Pentium 4 processor, please set "CPU Host Frequency" to 100MHz. If you use FSB533 Pentium 4 processor, please set "CPU Host Frequency" to 133MHz. If you use FSB800 Pentium 4 processor, please set "CPU Clock" to 200MHz. For power End-User use only! AGP/PCI/SRC Fixed Serial ATA device is very sensitive to SRC clock. SRC over clock may make Serial ATA device function can't work properly. Adjust AGP/PCI/SRC clock asynchronous with CPU. Memory Frequency For for FSB(Front Side Bus) frequency=400MHz, 2. 66 Memory Frequency = Host clock X 2. 66. (Default value) for FSB(Front Side Bus) frequency=533MHz, 2. 0 Memory Frequency = Host clock X 2. 0. (Default value) for FSB(Front Side Bus) frequency=800MHz, 2. 0 1. 6 1. 33 Auto Memory Frequency = Host clock X 2. 0. (Default value) Memory Frequency(Mhz) The values depend on CPU Host Frequency(Mhz). GA-8IG1000 Series Motherboard - 54 - AGP/PCI/SRC Frequency(Mhz) The values depend on Fixed AGP/PCI/SRC Frequency. English AGP OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Set Set Set Set AGP AGP AGP AGP OverVoltage OverVoltage OverVoltage OverVoltage Control Control Control Control to to to to Normal. +0. 3V. DIMM OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Set Set Set Set DIMM DIMM DIMM DIMM OverVoltage Control to Normal. OverVoltage Control to +0. 3V. CPU Voltage Control Supports adjustable CPU Vcore from 0. 8375V to 1. 7600V by 0. 025V step. (Default value: Normal) Normal CPU Vcore Display your CPU Vcore Voltage. - 55 - BIOS Setup English Select Language (*) CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Figure 9: Select Language Select Language Multi-Language supports 7 languages. There are English, Japanese, French, Spanish, German, Simplified Chinese, Traditional Chinese. () * For GA-8IG1000 Pro-G only. - 56 - GA-8IG1000 Series Motherboard English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Load Fail-Safe Defaults Figure 10: Load Fail-Safe Defaults Load Fail-Safe Defaults (Y/N) ?Y Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. () * For GA-8IG1000 Pro-G only. - 57 BIOS Setup English Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Load Optimized Defaults Figure 11: Load Optimized Defaults Load Optimized Defaults (Y/N) ?Y Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. () * For GA-8IG1000 Pro-G only. - 58 - GA-8IG1000 Series Motherboard English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Change/Set/Disable Password Figure 12: Password Setting Enter Password : Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash When you select this function, the following message will appear at the center of the screen to assist you in creating a password. You may also press <Esc> to abort the selection and not enter a password. [. . . ] Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. Question 13: How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ?Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SCSI" 2. [. . . ]