User manual GIGABYTE GA-8IE800

[. . . ] When you installing AGP card, please make sure the follow ing notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X(3. 3V) card is not supported by Intel® 845 (E/G)/ Intel® 850(E) . Please insert an AGP 4X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X (3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] (Default value) Always power on the system when AC back. - 39 - BIOS Setup English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI1/PCI5 IRQ Assignment PCI2 IRQ Assignment PCI3 IRQ Assignment PCI4 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Level higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: PnP/PCI Configurations FPCI1/P CI5 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 1/ PCI 5. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI1/ PCI5. FPCI2 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 2. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI2. FPCI3 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 3. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI3. FPCI4 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 4. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI4. GA-8IE800 Motherboard - 40 - English PC Health Status CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PC Health Status Reset Case Open Status Case Opened VCORE Vcc18 +3. 3V +5V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning [Disabled] No 1. 488V 1. 776V 3. 296V 5. 053V 11. 840V 23°C 4440 RPM 0 RPM Disabled Disabled Disabled Item Help Menu Level higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure7: PC Health Status CReset Case Open Status CCase Opened If the case is closed, "Case Opened" will show "No". If the case have been opened, "Case Opened" will show "Yes". If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save CMOS, your computer will restart. Disabled : Don' reset case open status. ;Enabled : Clear case open status at next boot. t C Current Voltage (V) VCORE / Vcc18 /+3. 3V / +5V / +12V 8Detect system' voltage status automatically. s - 41 - BIOS Setup English CCurrent CPU Temperature 8Detect CPU Temp. automatically. C Current CPU/SYSTEM FAN Speed (RPM) 8Detect CPU/SYSTEM Fan speed status automatically. C CPU Warning Temperature 860°C / 140°F 870°C / 158°F 880°C / 176°F 890°C / 194°F 8Disabled Monitor CPU Temp. Disable this function. (Default value) C CPU FAN Fail Warning 8Disabled 8Enabled Fan Warning Function Disable. (Default value) Fan Warning Function Enable. C SYSTEM FAN F ail Warning 8Disabled 8Enabled Fan Warning Function Disable. (Default value) Fan Warning Function Enable. GA-8IE800 Motherboard - 42 - Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Frequency/Voltage Control CPU Clock Ratio CPU Host Clock Control øCPU Host Frequency(MHz) øFixed PCI/AGP Frequency Host/DRAM Clock ratio MemoryFrequency(MHz) PCI/AGP Frequency(MHz) CPU Voltage Control DIMM OverVoltage Control AGP OverVoltage Control [ 15X] [Disabled] 100 33/66 [Auto] 266 33/66 [Normal] [Normal] [Normal] Item Help Menu Level English higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 8: Frequency/Voltage Control øThose items will be available when "CPU Host Clock Control" is set to Enabled. FCPU Clock Ratio This setup option will automatically assign by CPU detection. For Willamette CPU: 8X~23X default: 14X For C-Stepping P4: 8X, 10X~24X default: 15X For Northwood CPU: 12X~24X default: 16X The option will display " Locked"and read only if the CPU ratio is not changeable. FCPU Host Clock Control Note: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot . When time out occur, system will reset and run at CPU default Host clock at next boot. 8Disable 8Enable Disable CPU Host Clock Control. (Default value) Enable CPU Host Clock Control. FCPU Host Frequency (MHz) 8100MHz ~ 355MHzSet CPU Host Clock from 100MHz to 355MHz. FFixed PCI/AGP Frequency 8You can choose those mode to adjust PCI/AGP frequency. - 43 BIOS Setup FHost/DRAM Clock Ratio English or FSB(Front Side Bus) frequency=400MHz, 82. 0 82. 66 8Auto Memory Frequency = Host clock X 2. 0. (Default value) for FSB(Front Side Bus) frequency=533MHz, 82. 0 Memory Frequency = Host clock X 2. 0. (Default value) for FSB(Front Side Bus) frequency=667MHz, 82. 0 Memory Frequency = Host clock X 2. 0. (Default value) FMemory Frequency(Mhz) 8The values depend on CPU Host Frequency(Mhz) . F PCI/AGP Frequency(Mhz) 8Setup PCI/AGP frequency by adjusting CPU Host Frequency or Fixed PCI/AGP Frequency item. FCPU OverVoltage Control Increase CPU voltage may get stable for Over_Clock. (Default value) 8+5% / +7. 5% / +10% Increase voltage range as user selected. FAGP OverVoltage Control Increase AGP voltage may get stable for Over_Clock. [. . . ] Please refer to the user manual and check whether you have connected any cable that is not provided with the motherboard package to the USB Over Current pin in the Front USB Panel. If the cable is your own cable, please remove it from this pin and do not connect any of your own cables to it. English GA-8IE800 Motherboard - 80 - Question 10: Sometimes I hear different continuous beeps from computer after system boots up. Answer: The beep codes below may help you identify the possible computer problems. gAMI BIOS Beep Codes *Computer gives 1 short beep when system boots successfully. [. . . ]