User manual GIGABYTE GA-8IE2004P-L

[. . . ] When you installing AGP card, please make sure the follow ing notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X(3. 3V) card is not supported by Intel® 845 (E/G)/ Intel® 850(E) . Please insert an AGP 4X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X (3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] Disable onboard LPT port. FParallel Port Mode This feature allows you to connect with an advanced print via the port mode it supports. 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port . Using Parallel port as ECP & EPP mode. FECP Mode Use DMA 83 81 Set ECP mode use DMA 3. (Default value) Set ECP mode use DMA 1. FGame Port Address 8Disabled 8201 8209 Disabled this function. (Default Value) Enable Game port and address is 209. FMidi Port Address 8Disabled 8300 8330 Disabled this function. Enable Midi port and address is 330. (Default Value) FMidi Port IRQ 85 810 Midi Port use IRQ 5. (Default Value) GA-8IE2004P(-L) Motherboard - 38 - English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type Power LED in S1 State Soft-Off by PWR-BTTN PME Event Wake Up ModemRingOn Resume by Alarm ø Date(of Month) Alarm ø Time(hh:mm:ss) Alarm Power On By Mouse Power On By Keyboard øKB Power On Password AC Back Function [S1(POS)] [Blinking] [Instant-off] [Enabled] [Enabled] [Disabled] Everyday 0: 0: 0 [Disabled] [Disabled] Enter [Soft-Off] Item Help Menu Level higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Power Management Setup - 39 - BIOS Setup English FACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI Suspend Type to S1/POS (Power On Suspend). (Default value) Set ACPI Suspend Type to S3/STR (Suspend To RAM). C Power LED in S1 State 8Blinking 8Dual/Off In standby mode(S1), power LED will blink. If use dual color LED, power LED will turn to another color. FSoft-off by PWR-BTTN 8Instant-off 8Delay 4 Sec. Enter suspend if button is pressed less than 4 sec. FPME Event Wake up MWhen set at Enabled, any PCI-PM event awakes the system from a PCI-PM controlled state. MThis feature requires an ATX power supply that provides at least 1A on the +5VSB lead. (Default Value) FModem Ring On M An incoming call via modem awakes the system from its soft-off mode. 8Disabled 8Enabled Disabled Modem Ring On function. (Default Value) FResume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. (Default Value) Enable alarm function to POWER ON system. GA-8IE2004P(-L) Motherboard - 40 - If RTC Alarm Lead To Power On is Enabled. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : Everyday, 1~31 (0~23) : (0~59) : (0~59) English FPower On By Mouse 8Disabled 8Mouse Click Disabled this function. (Default value) Set mouse double click to power on system. F Power On By Keyboard This feature allows you to set the method for powering-on the system. The option " Password"allows you to set up to 5 alphanumeric characters to power-on the system. The option " Keyboard 98"allows you to use the standard keyboard 98 to power on the system. 8Password 8Disabled 8Keyboard 98 Enter from 1 to 5 characters to set the Keyboard Power On Password. (Default value) If your keyboard have " POWER Key"button, you can press the key to power on your system. FKB Power ON Password 8Enter Input password (from 1 to 5 characters) and press Enter to set the Key board Power On Password. . FAC Back Function 8Memory 8Soft-Off 8Full-On System power on depends on the status before AC lost. (Default value) Always power on the system when AC back. - 41 - BIOS Setup English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI1/PCI5 IRQ Assignment PCI2 IRQ Assignment PCI3 IRQ Assignment PCI4 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Level higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: PnP/PCI Configurations FPCI1/P CI5 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 1/ PCI 5. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI1/ PCI5. FPCI2 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 2. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI2. FPCI3 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 3. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI3. FPCI4 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 4. [. . . ] Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. Question 13:How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ?Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SCSI" 2. [. . . ]