User manual GIGABYTE GA-8ID533

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Do not use AGP 2X card (3. 3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845(E/G) / 850(E) chipset can't support AGP 2X(3. 3V). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/ 4X mode AGP slot. [. . . ] Disable onboard Serial port 2. C UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) 8ASKIR 8IrDA 8Normal Set onboard I/O chip UART to ASKIR Mode. (Default Value) C UR2 Dupl ex Mode 8Half 8Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. C Onboard Parallel port 8378/IRQ7 8278/IRQ5 8Disabled 83BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. - 33 BIOS Setup English CParallel Port Mode 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port. Using Parallel port as ECP & EPP mode. CECP Mode Use DMA 83 81 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. Disable this function. CMidi Port Address 8290 8300 8330 8Disabled Set Midi Port Address to 290. Set Midi Port Address to 330. (Default Value) Disable this function. CCIR Port Address 8310 8320 8Disabled Set CIR Port Address to 310. Disable this function. CCIR Port IRQ 85 811 Set CIR Port IRQ to 5. (Default Value) GA-8ID533 Motherboard - 34 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Pow er LED in S1 state Soft-Off by PWR_BTTN PME Ev ent Wake Up ModemRingOn Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function S1(POS) Blinking Instant-Off Enabled Enabled Disabled Ev ery day 000 Disabled Disabled Enter Soft-Off [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] Set suspend ty pe to Pow er On Suspend under ACPI OS higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Power LED i n S1 state 8Blinking 8Dual/Off In standby mode(S1), pow er LED w ill blink. If use dual color LED, pow er LED w ill turn to another color. C Soft-off by PWR_BTT N 8Instant-off 8Delay 4 Sec. - 35 BIOS Setup English FModemRingOn 8Disabled 8Enabled Disable Modem Ring On / Wake On LAN function. The modem ring / LAN w ake up w ill bring the sy stem out of soft-off or suspend state if this option is set "Enabled". (Default Value) C PME Event Wake Up 8Disabled 8Enabled Disable this function. (Default Value) C Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to pow er on sy stem. (Default Value) Enable alarm function to POWER ON sy stem. If RTC Alarm Lead To Pow er On is Enabled. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : Ev ery day , 1~31 (0~23) : (0~59) : (0~59) CPower On By Mouse 8Disabled 8Mouse Click Disabled this function. (Default v alue) Set mouse pow er on by double click mouse bottom. C Power On B y Keyboard 8Passw ord 8Disabled 8Key board 98 Enter from 1 to 5 characters to set the Key board Pow er On Passw ord. (Default v alue) If y our key board hav e "POWER Key " button, y ou can press the key to pow er on y our sy stem. CKB Power ON Password 8Enter Input passw ord (from 1 to 5 characters) and press Enter to set the Key board Pow er On Passw ord. CAC Back Function 8Memory 8Soft-Off 8Full-On Sy stem pow er on depends on the status before AC lost. - 36 - GA-8ID533 Motherboard English PnP/PCI Configurations CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are PnP/PCI Configurations PCI 1/ PCI5 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment PCI 4 IRQ Assignment Auto Auto Auto Auto Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e F6:Fail-Safe Defaults ESC:Ex it F1:General Help F5:Prev ious Values F7:Optimized Defaults Figure 6: PnP/PCI Configurations C PCI 1/PCI5 IRQ Assi gnment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1/ PCI5. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 1. C PCI 2 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 2. [. . . ] It can help you check out which kind of motherboard and which brand of Flash ROM are supported. In method I, if it shows two or more motherboard's model names to be selected, please make sure your motherboard's model name again. In method II, be sure that motherboard's model name in BIOS unzip file are the same as your motherboard's. In method I, if the BIOS file you need cannot be found in @BIOSTM server, please go onto Gigabyte's web site for downloading and updating it according to method II. [. . . ]